Kichler 42565 User Manual download pdf (Page 1)

CHAIN DROP INSTALLATION INSTRUCTIONS

1) Place bottom end of corner rod on top of corner of bottom

ring. Align hole in end of corner rod with hole in bottom of

ring.

2) Lower long threaded pipe down through hole in end of

corner rod and through hole in bottom ring.

3) Thread ﬁnial onto end of threaded pipe protruding from

bottom of ring. Tighten ﬁnial to secure rod in place. NOTE:

Sides of rod should be square with sides of bottom ring.

4) Repeat steps 1 - 3 for remaining corner rods.

5) Place top ring on top of corner rods passing holes in

corners of top ring over ends of threaded pipes protruding

from tops of corner rods.

6) Lower arm down onto top ring. Pass hole in tab on end of

arm over threaded pipe protruding from top of ring.

7) Thread ﬁnial onto end of threaded pipe protruding from top

of ring.

8) Repeat steps 5-7 for remaining arms.

9) Pass wire from center stem on ﬁxture body through hole in

bottom of top trim piece and up through loop on top trim

piece.

10) Screw top trim piece onto top of center stem.

11) Align hole in top of arm with hole on side of sphere on top

trim.

12) Thread ball stud into hole in arm and into hole in side of

sphere. Tighten ball stud to secure arm in place.

13) Repeat steps 11 and 12 for remaining arms.

14) After arms are attached to sphere, completely tighten ﬁnials

on bottom of arms to secure arms in place.

15) Pass threaded pipe on end of small loop through hole in

canopy.

16) Pass hole in lockwasher over end of threaded pipe protruding

from inside canopy. Thread hexnut onto end of threaded

pipe. Tighten hexnut to secure canopy to ﬁxture.

17) TURN OFF POWER.

IMPORTANT: Before you start, NEVER attempt any work

without shutting off the electricity until the work is done.

a) Go to the main fuse, or circuit breaker, box in your

home. Place the main power switch in the “OFF” position.

b) Unscrew the fuse(s), or switch “OFF” the circuit breaker

switch(s), that control the power to the ﬁxture or room

that you are working on.

c) Place the wall switch in the “OFF” position. If the ﬁxture

to be replaced has a switch or pull chain, place those in

the “OFF” position.

18) Find the appropriate threaded holes on mounting strap.

Assemble mounting screws into threaded holes.

19) Attach mounting strap to outlet box. (Screws not provided)

Mounting strap can be adjusted to suit position of ﬁxture.

20) Make wire connections (connectors not provided.) Reference

chart below for correct connections and wire accordingly.

21) Push ﬁxture to ceiling, carefully passing mounting screws

through holes in canopy.

22) Thread knurl knobs onto mounting screws. Tighten knurl

knobs to secure ﬁxture to ceiling.

SEMI FLUSH INSTALLATION INSTRUCTIONS

1) Remove loop from top trim piece.

2) Follow step #1-10 in Chain Drop Installation Instructions.

11) Pass hole in canopy down over end of threaded pipe on top

trim. Set canopy on top of top trim piece.

12) Pass hole in lockwasher over end of threaded pipe protruding

from inside canopy. Thread hexnut onto end of threaded

pipe. Tighten hexnut to secure canopy to ﬁxture.

13) Follow step #17-22 in Chain Drop Installation Instructions.

Connect Black or

Red Supply Wire to:

Connect

White Supply Wire to:

Black White

*Parallel cord (round & smooth) *Parallel cord (square & ridged)

Clear, Brown, Gold or Black

without tracer

Clear, Brown, Gold or Black

with tracer

Insulated wire (other than green)

with copper conductor

Insulated wire (other than green)

with silver conductor

*Note: When parallel wires (SPT I & SPT II)

are used. The neutral wire is square shaped

or ridged and the other wire will be round in

shape or smooth (see illus.)

Neutral Wire

Date Issued: 11/8/13

IS-42565-CB

MOUNTING STRAP

COLLIER DE FIXATION

INSTRUCTIONS

For Assembling and Installing Fixtures in Canada

Pour L’assemblage et L’installation Au Canada

SEE OTHER SIDE FOR CANADIAN FRENCH TRANS-

LATIONS.

VOIR L’AUTRE CÔTÉ POUR LES CANADIENS TRA-

DUCTIONS EN FRANÇAIS.

CANOPY

CACHE

KNURL KNOB

BOULE

LOOP

ANNEAU

MOUNTING STRAP

COLLIER DE FIXATION

HEXNUT

ECROU HEXAGONAL

LOCKWASHER

RONDELLE DE BLOCAGE

CANOPY

CACHE

KNURL KNOB

BOULE

LOOP

ANNEAU

FINIAL

ORNEMENT

ARM

BRAS

FIXTURE BODY

LUMINAIRE

TOP TRIM

GARNITURE

SUPÉRIEURE

FINIAL

ORNEMENT

BALL STUD

GOUJON À BILLE

TOP RING

ANNEAU SUPÉRIEUR

CORNER ROD

TIGE EN COIN

BOTTOM RING

ANNEAU INFÉRIEUR

TAB

ONGLET

CHAIN DROP INSTALLATION

INSTALLATION EN CHUTE DE CHAÎNE

SEMI FLUSH INSTALLATION

INSTALLATION SEMI-ENCASTRÉE

ARM

BRAS

FINIAL

ORNEMENT

BALL STUD

GOUJON À BILLE

TAB

ONGLET

FINIAL

ORNEMENT

FIXTURE BODY

LUMINAIRE

TOP RING

ANNEAU SUPÉRIEUR

CORNER ROD

TIGE EN COIN

BOTTOM RING

ANNEAU INFÉRIEUR

CENTER STEM

TIGE CENTRALE

CENTER STEM

TIGE CENTRALE

LONG THREADED PIPE

LONG TUBE FILETÉ

LONG THREADED PIPE

LONG TUBE FILETÉ

1 2

LATIONS 1
DUCTIONS EN FRANÇAIS 1

Summary of Contents

Page 1 - DUCTIONS EN FRANÇAIS

CHAIN DROP INSTALLATION INSTRUCTIONS1) Place bottom end of corner rod on top of corner of bottom ring. Align hole in end of corner rod with hole i

Page 2

INSTRUCTIONS POUR INSTALLATION EN CHUTE DE CHAÎNE1) Placer l’extrémité inférieure de la tige en coin sur la partie supérieure du coin de l’anneau

Kichler 42565 User Manual Page 1

Browse online or download User Manual for Lighting Kichler 42565. Kichler 42565 Manuel d'utilisation

Summary of Contents

More documents for Lighting Kichler 42565

Comments to this Manuals

Kichler 42565 User Manual Page 1

Browse online or download User Manual for Lighting Kichler 42565. Kichler 42565 Manuel d'utilisation

Summary of Contents

More documents for Lighting Kichler 42565

Comments to this Manuals

Related products and manuals for Lighting Kichler 42565