Kichler 43193 User Manual download pdf

1) Rotate arms until evenly spaced.

2) Lower ﬁxture body into the center of ring.

3) Pass holes in tabs at ends of each arm over threaded studs

along inside of ring.

4) Screw threaded caps onto ends of each threaded stud.

5) Once all arms are attached with threaded caps, completely

tighten threaded caps to secure ﬁxture body to ring.

6) Screw threaded pipe into top of ﬁxture body.

7) Pass hole in cap down over end of threaded pipe on top of

ﬁxture body.

8) Screw coupling onto end of threaded pipe protruding from

top of cap

9) Pass ﬁxture wire through stem and screw stem to coupling.

NOTE: Thread locking compound must be applied to all

stem threads as noted with symbol (3) to prevent accidental

rotation of ﬁxture during cleaning, relamping, etc.

10) Pass wire through remaining stems and screw stems

together.

11) Attach small loop to top of last stem.

12) TURN OFF POWER.

IMPORTANT: Before you start, NEVER attempt any work

without shutting off the electricity until the work is done.

a) Go to the main fuse, or circuit breaker, box in your

home. Place the main power switch in the “OFF” position.

b) Unscrew the fuse(s), or switch “OFF” the circuit breaker

switch(s), that control the power to the ﬁxture or room that

you are working on.

c) Place the wall switch in the “OFF” position. If the ﬁxture

to be replaced has a switch or pull chain, place those in

the “OFF” position.

13) Take threaded pipe from parts bag and screw in screw collar

loop a minimum of 6 mm (1/4”). Lock into place with hexnut.

14) Run another hexnut down threaded pipe almost touching

ﬁrst hexnut. Now screw threaded pipe into mounting strap.

Mounting strap must be positioned with extruded thread

faced into outlet box. Threaded pipe must protrude out the

back of mounting strap. Connect mounting strap to outlet

box.

15) Unscrew the threaded ring from screw collar loop. Take

canopy and pass over screw collar loop. Approximately one

half of the screw collar loop exterior threads should be

exposed. Adjust screw collar loop by turning assembly up or

down in mounting strap. Remove canopy.

16) After desired position is found, tighten top hexnut up against

the bottom of the mounting strap.

17) Slip canopy over screw collar loop and thread on threaded

ring. Attach chain (with ﬁxture connected) to bottom of

screw collar loop. Unscrew threaded ring, let canopy and

threaded ring slip down.

18) Weave electrical wire and ground wire through chain links no

more than 3 inches apart. Pass wire through threaded ring,

canopy, screw collar loop, threaded pipe and into outlet box.

19) Connect ﬁxture ground wire to outlet box ground wire with

wire connector. (Not provided.) Never connect ground wire

to black or white power supply wire.

20) Make wire connections (connectors not provided). Reference

chart below for correct connections and wire accordingly.

21) Raise canopy to ceiling

22) Secure canopy in place by tightening threaded ring onto

screw collar loop.

23) Slip glass over socket and secure in place with socket ring.

Connect Black or

Red Supply Wire to:

Connect

White Supply Wire to:

Black White

*Parallel cord (round & smooth) *Parallel cord (square & ridged)

Clear, Brown, Gold or Black

without tracer

Clear, Brown, Gold or Black

with tracer

Insulated wire (other than green)

with copper conductor

Insulated wire (other than green)

with silver conductor

*Note: When parallel wires (SPT I & SPT II)

are used. The neutral wire is square shaped

or ridged and the other wire will be round in

shape or smooth (see illus.)

Neutral Wire

Date Issued: 10/4/13 IS-43193-CB

INSTRUCTIONS

For Assembling and Installing Fixtures in Canada

Pour L’assemblage et L’installation Au Canada

FIXTURE BODY

LUMINAIRE

MOUNTING STRAP

PATTE DE FIXATION

HEXNUT

ECROU HEXAGONAL

THREADED PIPE

TUBE FILETÉ

SCREW COLLAR LOOP

COLLIER-ÉCROU

CANOPY

CACHE

THREADED RING

BAGUE FILETÉE

LOOP

BOUCLE

GLASS

VERRE

STEM

TIGE

SEE OTHER SIDE FOR CANADIAN FRENCH TRANS-

LATIONS.

VOIR L’AUTRE CÔTÉ POUR LES CANADIENS TRA-

DUCTIONS EN FRANÇAIS.

We’re here to help 866-558-5706

Hrs: M-F 9am to 5pm EST

COUPLING

ACCOUPLEMENT

CAP

THREADED PIPE

TUBE FILETÉ

RING

THREADED CAP

ARM

BRAS

1 2

866-558-5706 1

Summary of Contents

Page 1 - 866-558-5706

1) Rotate arms until evenly spaced.2) Lower ﬁxture body into the center of ring.3) Pass holes in tabs at ends of each arm over threaded studs a

Page 2

1) Tourner les bras jusqu’à ce que l’espacement soit uniforme.2) Abaisser le luminaire dans le centre de l’anneau.3) Passer les trous dans les lan

Kichler 43193 User Manual

Browse online or download User Manual for Lighting Kichler 43193. Kichler 43193 Manuel d'utilisation

Summary of Contents

More documents for Lighting Kichler 43193

Comments to this Manuals

Kichler 43193 User Manual

Browse online or download User Manual for Lighting Kichler 43193. Kichler 43193 Manuel d'utilisation

Summary of Contents

More documents for Lighting Kichler 43193

Comments to this Manuals

Related products and manuals for Lighting Kichler 43193