Kichler 42172 User Manual download pdf

Adjusting position of xture after installation for leveling purposes of

one inch or less:

NOTE: Center cable will adjust height of xture. Side cables will adjust level

of xture.

TO RAISE FIXTURE: Push cable up into xture body. Release cable and

cable will lock into place.

TO LOWER FIXTURE: Push button in on cable adjuster and pull cable

down. Release button to lock cable in place.

NOTE: With button pushed in cable will raise and lower. Without button

pushed in cable will only raise up and lock in place. (SEE: CABLE ADJUST-

MENT DETAIL)

IMPORTANT SAFETY INSTRUCTIONS

LIGHTED BULB IS HOT!

WARNING: To reduce the risk of FIRE or INJURY TO PERSON:

• Turn off and allow to cool before replacing bulb.

• Bulb gets HOT QUICKLY! Contact switch only when turning off.

• DO NOT remain in light if skin feels warm. (Light is intense, may cause

“sunburn”)

• DO NOT look directly at lighted bulb.

• Keep materials away from bulb that may burn.

• Use ONLY with wattage specied or lower.

• DO NOT touch bulb at any time, use a soft cloth. Oil from skin may damage

bulb.

• DO NOT operate xture with missing or damaged glass.

1) TURN OFF POWER.

IMPORTANT: Before you start, NEVER attempt any work without

shutting off the electricity until the work is done.

a) Go to the main fuse, or circuit breaker, box in your home. Place

the main power switch in the “OFF” position.

b) Unscrew the fuse(s), or switch “OFF” the circuit breaker switch(s),

that control the power to the xture or room that you are working on.

c) Place the wall switch in the “OFF” position. If the xture to be

replaced has a switch or pull chain, place those in the “OFF”

position.

2) Assemble mounting screws into threaded holes in mounting strap.

3) Attach mounting strap to outlet box. (Screws not provided)

4) Make wire connections (connectors not provided.) Reference chart

below for correct connections and wire accordingly.

IMPORTANT: For xtures 42172, 42173 and 42174, the wires on these

xtures will be clear or silver. The “Black” xture wire should be marked with

an “L”. The “White” xture wire should be marked with an “N”. The “White”

supply wire does have a thin white wire that runs through the clear/silver wire.

5) Push xture to ceiling, carefully passing mounting screws through holes.

6) Secure xture to ceiling with threaded balls.

8) Insert recommended bulb. CAUTION: DO NOT touch bulb with bare

hands. If this happens, clean bulb with denatured alcohol and a lint free

cloth.

9) Thread glass sleeve onto socket. (DO NOT over tighten.)

10) Lower each crystal rod down through top and bottom triangular opening

on xture. Peg on crystal will keep crystal in place on xture.

Connect Black or

Red Supply Wire to:

Connect

White Supply Wire to:

Black White

*Parallel cord (round & smooth) *Parallel cord (square & ridged)

Clear, Brown, Gold or Black

without tracer

Clear, Brown, Gold or Black

with tracer

Insulated wire (other than green)

with copper conductor

Insulated wire (other than green)

with silver conductor

*Note: When parallel wires (SPT I & SPT II)

are used. The neutral wire is square shaped

or ridged and the other wire will be round in

shape or smooth (see illus.)

Neutral Wire

MOUNTING STRAP

COLLLIER DE FIXATION

Date Issued: 6/8/12 IS-42172-CB

INSTRUCTIONS

For Assembling and Installing Fixtures in Canada

Pour L’assemblage et L’installation Au Canada

PRESSED

CABLE ADJUSMENT DETAIL

DÉTAILS D’AJUSTEMENT DU CÂBLE

NOT

PRESSED

UP & DOWN

UP ONLY

FIXTURE

LUMINAIRE

THREADED BALL

BOULE FILETÉ

SIDE CABLE

CABLE LATERAL

CRYSTAL ROD

TIGE EN CRISTAL

TRIANGULAR OPENING

OUVERTURE TRIANGULAIRE

SEE OTHER SIDE FOR CANADIAN FRENCH TRANS-

LATIONS.

VOIR L’AUTRE CÔTÉ POUR LES CANADIENS TRA-

DUCTIONS EN FRANÇAIS.

STRAIN RELIEF

SERRE-CÂBLE

WIRE

FILS

1) If strain relief is not assembled to wires, pull wires up through strain

relief and close strain relief.

2) Holding strain relief with pliers, pinch sides of strain relief and push

strain relief up through hole in canopy. (REF: FIG. 2)

3) If strain relief is assembled to canopy, to remove strain relief to

release strain on wires, from inside canopy pinch sides of strain relief

with pliers. Push strain relief down through hole in canopy. (REF: FIG. 1)

4) Open strain relief and pull wires down. Close strain relief and replace

strain relief to canopy (see step #2).

CAUTION: Take care not to nick, cut or damage wire.

CANOPY

CACHE

PLIERS

PINCES

STRAIN RELIEF

SERRE-CÂBLE

STRAIN RELIEF

SERRE-CÂBLE

PLIERS

PINCES

CANOPY

CACHE

WIRE

FILS

FIG. 1

FIG. 2

STRAIN RELIEF

SERRE-CÂBLE

1 2

Summary of Contents

Page 1 - DUCTIONS EN FRANÇAIS

Adjusting position of xture after installation for leveling purposes of one inch or less:NOTE: Center cable will adjust height of xture. Side cables

Page 2 - DÉTAILS D’AJUSTEMENT DU CÂBLE

5) Pousser le luminaire vers le plafond en passant soigneusement les vis de montage par les trous.6) Fixer le luminaire au plafond à l’aide des b

Related models: 42174 | 42173 |

Comments to this Manuals

No comments

Kichler 42172 User Manual

Browse online or download User Manual for Lighting Kichler 42172. Kichler 42172 Manuel d'utilisation

Summary of Contents

Related models: 42174 | 42173 |

Comments to this Manuals

Related products and manuals for Lighting Kichler 42172