1) To install glass panels: Carefully insert glass panel inside
cage. Fit top edge of glass panel into channel along top
inside of cage. Press glass panel up against inside of cage.
Place bracket inside cage. Align hole in step of bracket with
hole in bottom edge of cage. Thread screw up through hole
in bracket and into hole in cage. Tighten screw to secure
bracket and glass panel in place. Repeat these steps for
remaining glass panels.
2) Lower top trim down. Set top trim down on top of fixture.
Align hole in top trim with hole in coupling on top of fixture.
3) Pass end of threaded pipe through hole in top trim. Screw
end of threaded pipe into coupling.
4) Thread loop onto end of threaded pipe protruding from top
trim.
5) TURN OFF POWER.
IMPORTANT: Before you start, NEVER attempt any work
without shutting off the electricity until the work is done.
a) Go to the main fuse, or circuit breaker, box in your
home. Place the main power switch in the “OFF”
position.
b) Unscrew the fuse(s), or switch “OFF” the circuit breaker
switch(s), that control the power to the fixture or room
that you are working on.
c) Place the wall switch in the “OFF” position. If the fixture
to be replaced has a switch or pull chain, place those in
the “OFF” position.
6) Find the appropriate threaded holes on mounting strap.
Assemble mounting screws into threaded holes.
7) Attach mounting strap to outlet box. (Screws not provided).
Mounting strap can be adjusted to suit position of fixture.
8) Grounding instructions: (See Illus. A or B).
A) On fixtures where mounting strap is provided with a hole
and two raise dimples. Wrap ground wire from outlet
box around green ground screw, and thread into hole.
B) On fixtures where a cupped washer is provided. Attach
ground wire from outlet box under cupped washer and
green ground screw, and thread into mounting strap.
If fixture is provided with ground wire. Connect fixture
ground wire to outlet box ground wire with wire connector.
(Not provided.) After following the above steps. Never connect
ground wire to black or white power supply wires.
9) Make wire connections (connectors not provided.) Reference
chart below for correct connections and wire accordingly.
10) Push fixture to wall, carefully passing mounting screws
through holes in fixture.
11) Thread threaded balls onto mounting screws. Tighten
threaded balls to secure fixture to wall.
INSTRUCTIONS FOR MOUNTING FIXTURE OUTDOORS AND/
OR IN WET LOCATIONS.
12) Mounting surface should be clean, dry, flat and 1/4” larger
that the canopy on all sides. Any gaps between the mounting
surface and canopy exceeding 3/16” should be corrected
as required.
13) With silicone caulking compound, caulk completely around
where back of canopy meets the wall surface to prevent
water from seeping into outlet box.
Date Issued: 12/26/14 IS-49580-US
MOUNTING STRAP
PLANCHA PARA
MONTAR
GREEN GROUND
CUPPED
WASHER
A
B
OUTLET BOX
GROUND
FIXTURE
GROUND
DIMPLES
WIRE CONNECTOR
(NOT PROVIDED)
OUTLET BOX
GROUND
GREEN GROUND
SCREW
FIXTURE
GROUND
Connect Black or
Red Supply Wire to:
Connect
White Supply Wire to:
Black White
*Parallel cord (round & smooth) *Parallel cord (square & ridged)
Clear, Brown, Gold or Black
without tracer
Clear, Brown, Gold or Black
with tracer
Insulated wire (other than green)
with copper conductor
Insulated wire (other than green)
with silver conductor
*Note: When parallel wires (SPT I & SPT II)
are used. The neutral wire is square shaped
or ridged and the other wire will be round in
shape or smooth (see illus.)
Neutral Wire
SEE OTHER SIDE FOR SPANISH TRANSLATIONS.
VEA EL OTRO LADO DE TRADUCCIONES AL ESPAÑOL.
THREADED BALL
BOLA ROSCADO
We’re here to help 866-558-5706
Hrs: M-F 9am to 5pm EST
GLASS PANEL INSTALLATION DETAIL
DETALLE DE INSTALACIÓN DEL PANEL DE VIDRIO
BRACKET
SOPORTE
SCREW
TORNILLO
LOOP
ANILLO
CAGE
JAULA
GLASS PANEL
PANEL DE CRISTAL
ROOF
TECHO
THREADED PIPE
TUBO ROSCADO
TOP TRIM
ADORNO SUPERIOR
COUPLING
ACOPLAMIENTO
(2 pages)
(2 pages)
Manymanuals.com
Manymanuals.de
Manymanuals.fr
Manymanuals.it
Manymanuals.pl
Manymanuals.cz
Manymanuals.es
Manymanuals-pt.com
Comments to this Manuals