Kichler 49505 User Manual download pdf

1) To install glass panels: From top of cage, lower glass panel

down inside ﬁxture. Fit bottom edge of glass into channel

along bottom inside of cage. Press glass panel up against

inside of cage. Place bracket inside cage. Align hole in step

of bracket with hole in top edge of cage above glass panel.

Thread screw down through hole in bracket and into hole in

cage. Keep bottom step of bracket gently pressed against

glass panel. (See FIG. 2 for glass panel installation detail.)

Repeat these steps for remaining glass panels.

2) Insert recommended bulb.

3) Set roof down on top of cage ﬁtting socket cluster inside

cage.

4) Thread screws down through holes along top edge of roof

and into holes in cage. Tighten screws to secure roof in place.

5) Thread loop onto threaded pipe on top of roof.

6) TURN OFF POWER.

IMPORTANT: Before you start, NEVER attempt any work

without shutting off the electricity until the work is done.

a) Go to the main fuse, or circuit breaker, box in your

home. Place the main power switch in the “OFF”

position.

b) Unscrew the fuse(s), or switch “OFF” the circuit breaker

switch(s), that control the power to the ﬁxture or room

that you are working on.

c) Place the wall switch in the “OFF” position. If the ﬁxture

to be replaced has a switch or pull chain, place those in

the “OFF” position.

7) Take threaded pipe from parts bag and screw in screw collar

loop a minimum of 6 mm (1/4”). Lock into place with hexnut.

8) Run another hexnut down threaded pipe almost touching

ﬁrst hexnut. Now screw threaded pipe into mounting strap.

Mounting strap must be positioned with extruded thread

faced into outlet box. Threaded pipe must protrude out the

back of mounting strap. Screw third hexnut onto end of

threaded pipe protruding from back of mounting strap.

9) Connect mounting strap to outlet box.

10) Unscrew the threaded ring from screw collar loop. Take

canopy and pass over screw collar loop. Approximately one

half of the screw collar loop exterior threads should be

exposed. Adjust screw collar loop by turning assembly up or

down in mounting strap. Remove canopy.

11) After desired position is found, tighten both top and bottom

hexnuts up against the bottom and top of the mounting

strap.

12) Slip canopy over screw collar loop and thread on threaded

ring. Attach chain (with ﬁxture connected) to bottom of

screw collar loop. Unscrew threaded ring, let canopy and

threaded ring slip down.

13) Weave electrical wire and ground wire through chain links no

more than 3 inches apart. Pass wire through threaded ring,

canopy, screw collar loop, threaded pipe and into outlet box.

14) Connect ﬁxture ground wire to outlet box ground wire with

wire connector. (Not provided.) Never connect ground wire

to black or white power supply wire.

15) Make wire connections (connectors not provided). Reference

chart below for correct connections and wire accordingly.

16) Raise canopy to ceiling.

17) Secure canopy in place by tightening threaded ring onto

screw collar loop.

Date Issued: 10/25/13 IS-49505-CB

Connect Black or

Red Supply Wire to:

Connect

White Supply Wire to:

Black White

*Parallel cord (round & smooth) *Parallel cord (square & ridged)

Clear, Brown, Gold or Black

without tracer

Clear, Brown, Gold or Black

with tracer

Insulated wire (other than green)

with copper conductor

Insulated wire (other than green)

with silver conductor

*Note: When parallel wires (SPT I & SPT II)

are used. The neutral wire is square shaped

or ridged and the other wire will be round in

shape or smooth (see illus.)

Neutral Wire

INSTRUCTIONS

For Assembling and Installing Fixtures in Canada

Pour L’assemblage et L’installation Au Canada

MOUNTING STRAP

PATTE DE FIXATION

HEXNUT

ECROU HEXAGONAL

THREADED PIPE

TUBE FILETÉ

SCREW COLLAR LOOP

COLLIER-ÉCROU

CANOPY

CACHE

THREADED RING

BAGUE FILETÉE

LOOP

ANNEAU

ROOF

TOIT

THREADED PIPE

TUBE FILETÉ

SCREW

VIS

SOCKET

DOUILLE

CAGE

We’re here to help 866-558-5706

Hrs: M-F 9am to 5pm EST

GLASS PANEL INSTALLATION DETAIL

DÉTAILS DE L’INSTALLATION DU PANNEAU VITRÉ

BRACKET

SUPPORT

SCREW

TORNILLO

GLASS PANEL

PANNEAU VITRÉ

CAGE

JAULA

SEE OTHER SIDE FOR CANADIAN FRENCH TRANS-

LATIONS.

VOIR L’AUTRE CÔTÉ POUR LES CANADIENS TRA-

DUCTIONS EN FRANÇAIS.

GLASS PANEL

PANNEAU VITRÉ

1 2

866-558-5706 1

Summary of Contents

Page 1 - 866-558-5706

1) To install glass panels: From top of cage, lower glass panel down inside ﬁxture. Fit bottom edge of glass into channel along bottom inside o

Page 2

1) Pour installer les panneaux vitrés: Depuis la partie supérieure de la cage, abaisser le panneau vitré dans le luminaire. Placer le bord in

Comments to this Manuals

No comments

Kichler 49505 User Manual

Browse online or download User Manual for Lighting Kichler 49505. Kichler 49505 Manuel d'utilisation

Summary of Contents

Comments to this Manuals

Related products and manuals for Lighting Kichler 49505