1) TURN OFF POWER.
IMPORTANT: Before you start, NEVER attempt any work
without shutting off the electricity until the work is done.
a) Go to the main fuse, or circuit breaker, box in your home.
Place the main power switch in the “OFF” position.
b) Unscrew the fuse(s), or switch “OFF” the circuit breaker
switch(s), that control the power to the fixture or room that
you are working on.
c) Place the wall switch in the “OFF” position. If the fixture to
be replaced has a switch or pull chain, place those in the
“OFF” position.
2) Slip fixture over post and mark position of mounting holes in
post.
3) Remove fixture from post.
4) Drill 3/16” dia holes in post at positions marked .
5) If fixture is provided with ground wire, connect fixture ground
wire to outlet box ground wire with wire connector. (Not
provided). Never connect ground wire to black or white power
supply wires.
6) Make wire connections (connectors not provided). Reference
chart below for correct connections and wire accordingly.
7) Slip fixture over post and secure in place using provided
screws. Screws should slip into holes drilled in post.
8) Thread short end with hexnut of long threaded pipe into
coupling in center of socket cluster.
9) Insert recommended bulb.
10) Lower glass down and pass hole in bottom of glass over end
of long threaded pipe. Pass hole in bottom of glass over
socket cluster. Carefully place glass into bottom of cage.
11) Pass hole in rubber washer over end of threaded pipe
protruding from top of glass. Pass hole in flat washer over end
of threaded pipe. Screw hexnut onto end of threaded pipe.
(DO NOT over tighten.)
12) Lower top of cage down. Pass hole in top of cage over end of
threaded pipe protruding from top of glass.
13) Pass hole in cap over end of threaded pipe protruding from
top of cage. Set cap on top of cage.
14) Thread small washer onto end of threaded pipe protruding
from cap. Tighten washer up against cap.
15) Thread hex coupling onto end of threaded pipe protruding
from cap.
16) Lower first top trim down. Set top trim down on
top of fixture. Pass hole in top trim over coupling on top of
fixture.
17) Screw end of short threaded pipe with hexnut into coupling in
center of first top trim piece.
18) Pass hole in scalloped trim piece over end of threaded pipe
protruding from first top trim piece. Set scallped trim piece
down on top of first trim piece.
19) Pass hole in third trim piece over end of threaded pipe
protruding from top of scalloped trim. Set that trim piece down
on top of scalloped trim.
20) Thread finial onto end of threaded pipe protruding from last
trim piece. (DO NOT over tighten.)
Date Issued: 1/2/15 IS-49604-CB
Connect Black or
Red Supply Wire to:
Connect
White Supply Wire to:
Black White
*Parallel cord (round & smooth) *Parallel cord (square & ridged)
Clear, Brown, Gold or Black
without tracer
Clear, Brown, Gold or Black
with tracer
Insulated wire (other than green)
with copper conductor
Insulated wire (other than green)
with silver conductor
*Note: When parallel wires (SPT I & SPT II)
are used. The neutral wire is square shaped
or ridged and the other wire will be round in
shape or smooth (see illus.)
Neutral Wire
INSTRUCTIONS
For Assembling and Installing Fixtures in Canada
Pour L’assemblage et L’installation Au Canada
GLASS
VERRE
SCREW
VIS
We’re here to help 866-558-5706
Hrs: M-F 9am to 5pm EST
THREADED PIPE
TUBE FILETÉ
FIRST TOP TRIM
PREMIÈRE GARNITURE
SUPÉRIEURE
HEX COUPLING
ACCOUPLEMENT
HEXAGONAL
THIRD TOP TRIM PIECE
TROISIÈME PIÈCE DE
GARNITURE
BOTTOM CAGE
PARTIE INFÉRIEURE
DE LA CAGE
FINIAL
ORNEMENT
SCALLOPED TOP TRIM
PIECE
GARNITURE À BORDURE
FESTONNÉE
TOP CAGE
PARTIE
SUPÉRIEURE
DE LA CAGE
LONG THREADED PIPE
LONG TUBE FILETÉ
LOCKWASHER
RONDELLE DE BLOCAGE
CAP
CAPUCHON
RUBBER WASHER
RONDELLE
CAOUTCHOUTÉE
FLAT WASHER
RONDELLE PLATE
HEXNUT
ECROU HEXAGONAL
(1 pages)
(2 pages)
Manymanuals.com
Manymanuals.de
Manymanuals.fr
Manymanuals.it
Manymanuals.pl
Manymanuals.cz
Manymanuals.es
Manymanuals-pt.com
Comments to this Manuals