Kichler 43186 User Manual download pdf

1) Pass wire from ﬁxture through stems and screw stems into

couplings on top of ﬁxture body.

NOTE: Thread locking compound must be applied to all stem

threads as noted with symbol (3) to prevent accidental

rotation of ﬁxture during cleaning, relamping, etc.

2) Pass ﬁxture wire through remaining stems and screw stems

together.

3) The canopy has one set of loop/chain link/loop pre-installed.

Starting with that loop/chain link/loop, pass ﬁxture wire

through the threaded pipe on the ﬁrst small loop. Next pass

the ﬁxture wire through the hole in the small loop attached to

canopy and through the hole in the canopy.

4) With the set of loop/chain link/loop not pre-installed, from the

second set of stems, pass the ﬁxture wire through the hole in

the threaded pipe on the end of one small loop. Thread that

small loop to the end of the last stem.

5) Pass ﬁxture wire through hole in second small loop. Pass

ﬁxture wire through hole in canopy. Pass threaded pipe at end

of second loop through hole in canopy. Thread wing nut onto

end of threaded pipe. Tighten wing nut to secure loop to canopy.

6) TURN OFF POWER.

IMPORTANT: Before you start, NEVER attempt any work

without shutting off the electricity until the work is done.

a) Go to the main fuse, or circuit breaker, box in your home.

Place the main power switch in the “OFF” position.

b) Unscrew the fuse(s), or switch “OFF” the circuit breaker

switch(s), that control the power to the ﬁxture or room that

you are working on.

c) Place the wall switch in the “OFF” position. If the ﬁxture to

be replaced has a switch or pull chain, place those in the

“OFF” position.

7) Thread hexnut onto threaded pipe so that 5 threads are

exposed above hexnut. Thread that end of threaded pipe

into mounting strap and tighten hexnut against mounting strap.

8) Run another hexnut down threaded pipe almost touching

ﬁrst hexnut. Now screw threaded pipe into mounting strap.

Mounting strap must be positioned with extruded thread

faced into outlet box. Threaded pipe must protrude out the

back of mounting strap. Screw third hexnut onto end of

threaded pipe protruding from back of mounting strap.

9) Attach mounting strap to outlet box. (Screws not provided.)

10) Attach safety cable to slot in mounting strap.

11) Grounding instructions: (See Illus. A or B).

A) On ﬁxtures where mounting strap is provided with a hole

and two raise dimples. Wrap ground wire from outlet box

around green ground screw, and thread into hole.

B) On ﬁxtures where a cupped washer is provided. Put

ground wire from outlet box under cupped washer and

green ground screw and thread screw into hole in mounting

strap.

If ﬁxture is provided with ground wire. Connect ﬁxture ground

wire to outlet box ground wire with wire connector, (not

provided) after following the above steps. Never connect

ground wire to black or white power supply wires.

12) Make wire connections (connectors not provided.) Reference

chart below for correct connections and wire accordingly.

GREEN GROUND

SCREW

CUPPED

WASHER

OUTLET BOX

GROUND

FIXTURE

GROUND

DIMPLES

WIRE CONNECTOR

(NOT PROVIDED)

OUTLET BOX

GROUND

GREEN GROUND

SCREW

FIXTURE

GROUND

Connect Black or

Red Supply Wire to:

Connect

White Supply Wire to:

Black White

*Parallel cord (round & smooth)

*Parallel cord (square & ridged)

Clear, Brown, Gold or Black

without tracer

Clear, Brown, Gold or Black

with tracer

Insulated wire (other than green)

with copper conductor

Insulated wire (other than green)

with silver conductor

*Note: When parallel wires (SPT I & SPT II)

are used. The neutral wire is square shaped

or ridged and the other wire will be round in

shape or smooth (see illus.)

Neutral Wire

IS-43186-US

Date Issued: 7/25/14

SEE OTHER SIDE FOR SPANISH TRANSLATIONS.

VEA EL OTRO LADO DE TRADUCCIONES AL ESPAÑOL.

We’re here to help 866-558-5706

Hrs: M-F 9am to 5pm EST

13) Push ﬁxture to ceiling, carefully passing threaded pipe through

hole in canopy.

14) Thread hexnut onto end of threaded pipe protruding from

canopy. Tighten hexnut up against canopy.

15) Thread ﬁnial onto end of threaded pipe. (DO NOT over tighten.)

16) Set glass down over sockets.

MOUNTING STRAP

PLANCHA PARA MONTAR

CANOPY

ESCUDETE

STEM

VARILLA

HEXNUT

TUERCA HEXAGONAL

FINIAL

REMATE

SAFETY CABLE

CABLE DE SEGURIDAD

COUPLING

ACOPLAMIENTO

GLASS

VIDRIO

WING NUT

TUERCA DE MARIPOSA

SMALL LOOP

ARGOLLA PEQUEÑA

CHAIN LINK

ESLABÓN DE

CADENA

1 2

866-558-5706 1

Summary of Contents

Page 1 - 866-558-5706

1) Pass wire from ﬁxture through stems and screw stems into couplings on top of ﬁxture body. NOTE: Thread locking compound must be applied to all

Page 2

1) Pase el alambre del artefacto a través del vástago y atornille el vástago en el acoplamiento en la parte superior del el cuerpo del artefact

Related models: 42419 | 43191 |

Comments to this Manuals

No comments

Kichler 43186 User Manual

Browse online or download User Manual for Lighting Kichler 43186. Kichler 43186 User Manual

Summary of Contents

Related models: 42419 | 43191 |

Comments to this Manuals

Related products and manuals for Lighting Kichler 43186