Kichler 43121 User Manual download pdf

1) Screw long threaded pipe into coupling on top of ﬁxture body.

2) Pass hole in bottom of top column down over top of long

threaded pipe.

3) Lower top trim down over top of long threaded pipe. Set top

trim on top of center column.

4) Slip small washer then lockwasher over end of threaded

pipe. Thread hexnut onto end of threaded pipe.

5) Screw top hook onto end of threaded pipe.

6) TURN OFF POWER.

IMPORTANT: Before you start, NEVER attempt any work

without shutting off the electricity until the work is done.

a) Go to the main fuse, or circuit breaker, box in your home.

Place the main power switch in the “OFF” position.

b) Unscrew the fuse(s), or switch “OFF” the circuit breaker

switch(s), that control the power to the ﬁxture or room

that you are working on.

c) Place the wall switch in the “OFF” position. If the ﬁxture

to be replaced has a switch or pull chain, place those in

the “OFF” position.

7) Take threaded pipe from parts bag and screw in screw collar

loop a minimum of 6 mm (1/4”). Lock into place with hexnut.

8) Run another hexnut down threaded pipe almost touching

ﬁrst hexnut. Now screw threaded pipe into mounting strap.

Mounting strap must be positioned with extruded thread

faced into outlet box. Threaded pipe must protrude out the

back of mounting strap. Screw third hexnut onto end of

threaded pipe protruding from back of mounting strap.

9) Connect mounting strap to outlet box.

10) Unscrew the threaded ring from screw collar loop. Take canopy

and pass over screw collar loop. Approximately one half of

the screw collar loop exterior threads should be exposed.

Adjust screw collar loop by turning assembly up or down in

mounting strap. Remove canopy.

11) After desired position is found, tighten both top and bottom

hexnuts up against the bottom and top of the mounting strap.

12) Slip canopy over screw collar loop and thread on threaded

ring. Attach chain (with ﬁxture connected) to bottom of

screw collar loop. Unscrew threaded ring, let canopy and

threaded ring slip down.

13) Weave electrical wire and ground wire through chain links no

more than 3 inches apart. Pass wire through threaded ring,

canopy, screw collar loop, threaded pipe and into outlet box.

14) Connect ﬁxture ground wire to outlet box ground wire with

wire connector. (Not provided.) Never connect ground wire

to black or white power supply wire.

15) Make wire connections (connectors not provided). Reference

chart below for correct connections and wire accordingly.

16) Raise canopy to ceiling.

17) Secure canopy in place by tightening threaded ring onto

screw collar loop.

18) Attach crystals as illustrated.

Date Issued: 8/31/12 IS-43121-CB

Connect Black or

Red Supply Wire to:

Connect

White Supply Wire to:

Black White

*Parallel cord (round & smooth) *Parallel cord (square & ridged)

Clear, Brown, Gold or Black

without tracer

Clear, Brown, Gold or Black

with tracer

Insulated wire (other than green)

with copper conductor

Insulated wire (other than green)

with silver conductor

*Note: When parallel wires (SPT I & SPT II)

are used. The neutral wire is square shaped

or ridged and the other wire will be round in

shape or smooth (see illus.)

Neutral Wire

INSTRUCTIONS

For Assembling and Installing Fixtures in Canada

Pour L’assemblage et L’installation Au Canada

CRYSTAL A

CRYSTAL C

CRYSTAL K

CRYSTAL F

MOUNTING STRAP

PATTE DE FIXATION

HEXNUT

ECROU HEXAGONAL

THREADED PIPE

TUBE FILETÉ

SCREW COLLAR LOOP

COLLIER-ÉCROU

CANOPY

CACHE

THREADED RING

BAGUE FILETÉE

CRYSTAL A (6 pcs)

CRYSTAL C (30 pcs)

CRYSTAL F (19 pcs)

CRYSTAL K (1 pc)

CRYSTALS

CRISTAUX

SEE OTHER SIDE FOR CANADIAN FRENCH TRANS-

LATIONS.

VOIR L’AUTRE CÔTÉ POUR LES CANADIENS TRA-

DUCTIONS EN FRANÇAIS.

HOOK

CROCHET

TOP TRIM

GARNITURE SUPÉRIEURE

LONG THREADED PIPE

TUBE FILETÉ LONG

TOP COLUMN

COLONNE SUPÉRIEURE

LOCKWASHER

RONDELLE DE BLOCAGE

SMALL WASHER

PETIT RONDELLE

HEXNUT

ECROU HEXAGONAL

1 2

Summary of Contents

Page 1 - DUCTIONS EN FRANÇAIS

1) Screw long threaded pipe into coupling on top of ﬁxture body.2) Pass hole in bottom of top column down over top of long threaded pipe.3) L

Page 2 - CRYSTAL K (1 pc)

1) Visser le tube ﬁleté long dans l’accouplement sur l’extrémité supérieure du luminaire.2) Passer le trou situé en bas de la colonne supérieur

Kichler 43121 User Manual

Browse online or download User Manual for Lighting Kichler 43121. Kichler 43121 Manuel d'utilisation

Summary of Contents

More documents for Lighting Kichler 43121

Comments to this Manuals

Kichler 43121 User Manual

Browse online or download User Manual for Lighting Kichler 43121. Kichler 43121 Manuel d'utilisation

Summary of Contents

More documents for Lighting Kichler 43121

Comments to this Manuals

Related products and manuals for Lighting Kichler 43121