Kichler 43613 User Manual download pdf

15) Make wire connections (connectors not provided). Reference

chart below for correct connections and wire accordingly.

16) Raise canopy to ceiling.

17) Secure canopy in place by tightening threaded ring onto

screw collar loop.

18) Thread end of short threaded pipe into hex coupling on

bottom of cage.

19) Pass hole in bottom trim over end of short threaded pipe.

20) Thread ﬁnial onto end of short threaded pipe.

1) Pass ﬁxture wire from top of ﬁxture through hole in ﬁrst top

trim piece. Lower ﬁrst top trim down. Set top trim down on

top of ﬁxture. Pass hole in top trim over coupling on top of

ﬁxture.

2) Pass ﬁxture wire through end of threaded pipe with hexnut.

Screw that end of threaded pipe into coupling.

3) Pass ﬁxture wire through hole in scalloped trim piece. Set

trim piece down on top of ﬁrst trim.

4) Pass ﬁxture wire through hole in third trim piece. Set that

trim piece down on top of scalloped trim.

5) Pass ﬁxture wire through hole in bottom of loop. Thread loop

onto end of threaded pipe protruding from top trim.

6) TURN OFF POWER.

IMPORTANT: Before you start, NEVER attempt any work

without shutting off the electricity until the work is done.

a) Go to the main fuse, or circuit breaker, box in your

home. Place the main power switch in the “OFF”

position.

b) Unscrew the fuse(s), or switch “OFF” the circuit breaker

switch(s), that control the power to the ﬁxture or room

that you are working on.

c) Place the wall switch in the “OFF” position. If the ﬁxture

to be replaced has a switch or pull chain, place those in

the “OFF” position.

7) Take threaded pipe from parts bag and screw in screw collar

loop a minimum of 6 mm (1/4”). Lock into place with hexnut.

8) Run another hexnut down threaded pipe almost touching

ﬁrst hexnut. Now screw threaded pipe into mounting strap.

Mounting strap must be positioned with extruded thread

faced into outlet box. Threaded pipe must protrude out the

back of mounting strap. Screw third hexnut onto end of

threaded pipe protruding from back of mounting strap.

9) Connect mounting strap to outlet box.

10) Unscrew the threaded ring from screw collar loop. Take

canopy and pass over screw collar loop. Approximately one

half of the screw collar loop exterior threads should be

exposed. Adjust screw collar loop by turning assembly up or

down in mounting strap. Remove canopy.

11) After desired position is found, tighten both top and bottom

hexnuts up against the bottom and top of the mounting

strap.

12) Slip canopy over screw collar loop and thread on threaded

ring. Attach chain (with ﬁxture connected) to bottom of

screw collar loop. Unscrew threaded ring, let canopy and

threaded ring slip down.

13) Weave electrical wire and ground wire through chain links no

more than 3 inches apart. Pass wire through threaded ring,

canopy, screw collar loop, threaded pipe and into outlet box.

14) Grounding instructions: (See Illus. A or B).

A) On ﬁxtures where mounting strap is provided with a

hole and two raised dimples. Wrap ground wire from

outlet box around green ground screw, and thread into

hole.

B) On ﬁxtures where a cupped washer is provided. Attach

ground wire from outlet box under cupped washer and

green ground screw, and thread into mounting strap.

If ﬁxture is provided with ground wire. Connect ﬁxture

ground wire to outlet box ground wire with wire connector

(not provided.) after following the above steps. Never

connect ground wire to black or white power supply wires.

GREEN GROUND

SCREW

CUPPED

WASHER

OUTLET BOX

GROUND

FIXTURE

GROUND

DIMPLES

WIRE CONNECTOR

(NOT PROVIDED)

OUTLET BOX

GROUND

GREEN GROUND

SCREW

FIXTURE

GROUND

Connect Black or

Red Supply Wire to:

Connect

White Supply Wire to:

Black White

*Parallel cord (round & smooth) *Parallel cord (square & ridged)

Clear, Brown, Gold or Black

without tracer

Clear, Brown, Gold or Black

with tracer

Insulated wire (other than green)

with copper conductor

Insulated wire (other than green)

with silver conductor

*Note: When parallel wires (SPT I & SPT II)

are used. The neutral wire is square shaped

or ridged and the other wire will be round in

shape or smooth (see illus.)

Neutral Wire

Date Issued: 10/3/14 IS-43613-US

SEE OTHER SIDE FOR SPANISH TRANSLATIONS.

VEA EL OTRO LADO DE TRADUCCIONES AL ESPAÑOL.

MOUNTING STRAP

PLANCHA PARA MONTAR

LOOP

ANILLO

HEXNUT

TUERCA HEXAGONAL

THREADED PIPE

TUBO ROSCADO

THREADED RING

ANILLO ROSCADO

SCREW COLLAR LOOP

OJAL DE COLLAR

ROSCADO

We’re here to help 866-558-5706

Hrs: M-F 9am to 5pm EST

CANOPY

ESCUDETE

COUPLING

ACOPLAMIENTO

THREADED PIPE

TUBO ROSCADO

SHORT THREADED PIPE

TUBO ROSCADO CORTO

FINIAL

CAPUCHON

CAGE

JAULA

HEX COUPLING

ACOPLAMIENTO

HEXAGONAL

THIRD TOP TRIM PIECE

TERCERA GUARNICIÓN

SUPERIOR

BOTTOM TRIM

GUARNICIÓN INFERIOR

SCALLOPED TOP TRIM

PIECE

GUARNICIÓN FESTONEADA

FIRST TOP TRIM PIECE

PRIMERA GUARNICIÓN

SUPERIOR

1 2

866-558-5706 1

Summary of Contents

Page 1 - 866-558-5706

15) Make wire connections (connectors not provided). Reference chart below for correct connections and wire accordingly.16) Raise canopy to ceili

Page 2

1) Pase el cable desde la parte superior del artefacto de iluminación por el oriﬁcio situado en la primera guarnición superior. Descienda la

Kichler 43613 User Manual

Browse online or download User Manual for Lighting Kichler 43613. Kichler 43613 User Manual

Summary of Contents

More documents for Lighting Kichler 43613

Comments to this Manuals

Kichler 43613 User Manual

Browse online or download User Manual for Lighting Kichler 43613. Kichler 43613 User Manual

Summary of Contents

More documents for Lighting Kichler 43613

Comments to this Manuals

Related products and manuals for Lighting Kichler 43613