Kichler 43653 User Manual

Browse online or download User Manual for Lighting Kichler 43653. Kichler 43653 User Manual

  • Download
  • Add to my manuals
  • Print
  • Page
    / 2
  • Table of contents
  • BOOKMARKS
  • Rated. / 5. Based on customer reviews
Page view 0
16) Make wire connections (connectors not provided). Reference
chart below for correct connections and wire accordingly.
17) Raise canopy to ceiling.
18) Secure canopy in place by tightening threaded ring onto
screw collar loop.
19) Thread end of threaded pipe with bead into center of socket
cluster.
20) Thread hexnut onto end of threaded pipe.
21) Pass hole in flat washer over end of threaded pipe. Pass
hole in rubber washer over end of threaded pipe.
22) Raise glass up to fixture pass hole in glass over end of
threaded pipe.
23) Pass hole in rubber washer over end of threaded pipe
protruding from bottom of glass. Pass hole in flat washer
over end of threaded pipe. Screw hexnut onto end of
threaded pipe.
24) Pass hole in bottom trim over end of threaded pipe.
25) Thread finial onto end of threaded pipe. Tighten finial to
secure glass in place.
1) Lower long threaded pipe down through bottom center tube.
Pull fixture wire through long threaded pipe and make sure
fixture wire does not get pinched in bottom center tube.
2) Lower first decorative trim piece, decorative sphere then
second decorative trim piece down long threaded pipe. Pull
fixture wire through all three decorative pieces and make
sure fixture wire does not get pinch in between decorative
pieces.
3) Lower fixture body down. Pass top center tube down over
long threaded pipe. Pull fixture wire up at top of fixture body.
Make sure fixture wire does not get pinched in in top center
tube.
4) Pass fixture wire from top of fixture body through short
threaded pipe. Thread end of short threaded pipe into hole in
top of fixture body.
5) Pass fixture wire from small threaded pipe through hole in
center of top trim. Lower top trim down towards fixture.
Pass hole in top trim over end of small threaded pipe. Set
top trim down on top of fixture body.
6) Pass fixture wire through hole in bottom of top loop. Thread
top loop onto end of threaded pipe protruding from top trim.
7) TURN OFF POWER.
IMPORTANT: Before you start, NEVER attempt any work
without shutting off the electricity until the work is done.
a) Go to the main fuse, or circuit breaker, box in your
home. Place the main power switch in the “OFF”
position.
b) Unscrew the fuse(s), or switch “OFF” the circuit breaker
switch(s), that control the power to the fixture or room
that you are working on.
c) Place the wall switch in the “OFF” position. If the fixture
to be replaced has a switch or pull chain, place those in
the “OFF” position.
8) Take threaded pipe from parts bag and screw in screw collar
loop a minimum of 6 mm (1/4”). Lock into place with hexnut.
9) Run another hexnut down threaded pipe almost touching
first hexnut. Now screw threaded pipe into mounting strap.
Mounting strap must be positioned with extruded thread
faced into outlet box. Threaded pipe must protrude out the
back of mounting strap. Screw third hexnut onto end of
threaded pipe protruding from back of mounting strap.
10) Connect mounting strap to outlet box.
11) Unscrew the threaded ring from screw collar loop. Take
canopy and pass over screw collar loop. Approximately one
half of the screw collar loop exterior threads should be
exposed. Adjust screw collar loop by turning assembly up or
down in mounting strap. Remove canopy.
12) After desired position is found, tighten both top and bottom
hexnuts up against the bottom and top of the mounting
strap.
13) Slip canopy over screw collar loop and thread on threaded
ring. Attach chain (with fixture connected) to bottom of
screw collar loop. Unscrew threaded ring, let canopy and
threaded ring slip down.
14) Weave electrical wire and ground wire through chain links no
more than 3 inches apart. Pass wire through threaded ring,
canopy, screw collar loop, threaded pipe and into outlet box.
15) Grounding instructions: (See Illus. A or B).
A) On fixtures where mounting strap is provided with a
hole and two raised dimples. Wrap ground wire from
outlet box around green ground screw, and thread into
hole.
B) On fixtures where a cupped washer is provided. Attach
ground wire from outlet box under cupped washer and
green ground screw, and thread into mounting strap.
If fixture is provided with ground wire. Connect fixture
ground wire to outlet box ground wire with wire connector
(not provided.) after following the above steps. Never
connect ground wire to black or white power supply wires.
GREEN GROUND
SCREW
CUPPED
WASHER
A
B
OUTLET BOX
GROUND
FIXTURE
GROUND
DIMPLES
WIRE CONNECTOR
(NOT PROVIDED)
OUTLET BOX
GROUND
GREEN GROUND
SCREW
FIXTURE
GROUND
Connect Black or
Red Supply Wire to:
Connect
White Supply Wire to:
Black White
*Parallel cord (round & smooth) *Parallel cord (square & ridged)
Clear, Brown, Gold or Black
without tracer
Clear, Brown, Gold or Black
with tracer
Insulated wire (other than green)
with copper conductor
Insulated wire (other than green)
with silver conductor
*Note: When parallel wires (SPT I & SPT II)
are used. The neutral wire is square shaped
or ridged and the other wire will be round in
shape or smooth (see illus.)
Neutral Wire
Date Issued: 8/29/14 IS-43653-US
SEE OTHER SIDE FOR SPANISH TRANSLATIONS.
VEA EL OTRO LADO DE TRADUCCIONES AL ESPAÑOL.
MOUNTING STRAP
PLANCHA PARA MONTAR
LOOP
LAZO
HEXNUT
TUERCA HEXAGONAL
THREADED PIPE
TUBO ROSCADO
THREADED RING
ANILLO ROSCADO
SCREW COLLAR LOOP
OJAL DE COLLAR
ROSCADO
Were here to help 866-558-5706
Hrs: M-F 9am to 5pm EST
CANOPY
ESCUDETE
GLASS
VIDRIO
TOP TRIM
GUARNICIÓN
SUPERIOR
SHORT THREADED PIPE
TUBO ROSCADO CORTO
FIXTURE BODY
CUERPO DEL
ARTEFACTO
SOCKET CLUSTER
GRUPO DEL PORTALÁMPARAS
THREADED PIPE
TUBO ROSCADA
FLAT WASHER
ARANDELA PLANA
RUBBER WASHER
ARANDELA DE CAUCHO
FLAT WASHER
ARANDELA PLANA
RUBBER WASHER
ARANDELA DE CAUCHO
HEX COUPLING
ACOPLAMIENTO
HEXAGONAL
FINIAL
CAPUCHON
HEXNUT
TUERCA HEXAGONAL
BEAD
AISLADOR
BOTTOM TRIM
GUARNICIÓN INFERIOR
LONG THREADED PIPE
TUBO ROSCADO LARGO
BOTTOM CENTER TUBE
TUBO CENTRAL INFERIOR
DECORATIVE SPHERE
ESFERA DECORATIVA
DECORATIVE TRIM
DECORATIVA DE ADORNO
DECORATIVE TRIM
DECORATIVA DE ADORNO
TOP CENTER TUBE
TUBO CENTRAL SUPERIOR
SHORT THREADED PIPE
TUBO ROSCADO CORTO
Page view 0
1 2

Summary of Contents

Page 1 - 866-558-5706

16) Make wire connections (connectors not provided). Reference chart below for correct connections and wire accordingly.17) Raise canopy to ceili

Page 2

1) Descienda el tubo roscado largo a través del tubo central del fondo. Jale el alambre del artefacto a través del tubo roscado largo y asegur

Comments to this Manuals

No comments

VIA Technologies Mini-ITX Mainboard EPIA-SN manuales

Manuales del propietario y guías del usuario para Placas base VIA Technologies Mini-ITX Mainboard EPIA-SN.
Ofrecemos 1 manuales en pdf VIA Technologies Mini-ITX Mainboard EPIA-SN para descargar gratis por tipos de documentos: Manual de usuario


Tabla de contenidos

User’s Manual

1

Copyright

3

Trademarks

3

Macrovision

3

Disclaimer

3

Tested To Comply

4

With FCC Standards

4

FOR HOME OR OFFICE USE

4

Safety Instructions

5

ABLE OF

8

Specifications

11

AINBOARD

12

PECIFICATIONS

12

Chapter 1

16

Installation

17

C7 NanoBGA2

18

Memory Slot: DDR2 DIMM

19

ATX 20-Pin Power Connector

20

Audio Port

22

IDE Connector: IDE

23

Serial Port Connector: COM2

29

V_CF_SEL

32

ROM Write Protection: WP

33

JWLESS-LED1

34

PCI Express: PCIe x16

36

BIOS Setup

37

NTERING

38

Keys Description

39

AVIGATING THE

40

Chapter 3

42

Exit (Exit Options)

44

DVANCED

46

Remote Access Configuration

47

Trusted Computing

47

USB Configuration

47

ONFIGURATION

48

SATA Controller

49

SATA Option ROM

49

Hard Disk Write Protect

49

IDE Detect Time Out (Sec)

50

LBA/Large Mode

51

PIO Mode

52

DMA Mode

52

S.M.A.R.T

52

32 Bit Data Transfer

53

ARDWARE

55

General ACPI Configuration

56

Advanced ACPI Configuration

56

Chipset Configuration

56

Suspend Type

57

Repost Video on S3 Resume

57

USB Device Wakeup Function

59

Items Description

62

Remote Access

65

OMPUTING

66

Port 64/60 Emulation

68

USB 2.0 Controller Mode

68

BIOS EHCI Hand-Off

68

Clear NVRAM

69

Plug & Play O/S

69

Boot Settings Configuration

71

ETTINGS

72

PS/2 Mouse Support

73

Wait For ‘F1’ If Error

73

Hit ‘DEL’ Message Display

73

Interrupt 19 Capture

73

ECURITY

74

Change Supervisor Password

75

Change User Password

75

Boot Sector Virus Protection

76

Primary Graphics Adapter

79

AGP Aperture Size

79

Output Port

81

Dithering

81

HDAC Audio Controller

83

Save Changes and Exit

84

Discard Changes and Exit

85

Discard Changes

85

Load Optimal Defaults

86

Load Failsafe Defaults

87

Driver Installation

89

Getting Started

90

Note:

91

Chapter 4

92





Más productos y manuales para Placas base VIA Technologies

Modelos Tipo de documento
Computer Hardware 3301770 Manual de usuario   VIA Technologies Computer Hardware 3301770 User's Manual, 114 paginas
VB6002 Manual de usuario   VIA Technologies VB6002 User's Manual, 16 paginas