MOUNTING STRAP
ABRAZADERA DE MONTAJE
NOTE: Height of fixture must be adjusted before fixture is
mounted to ceiling.
1) Loosen threaded stud on strain relief on canopy. Insert cord
into hole in strain relief and up into canopy.
2) To adjust the length of the cord to achieve the desired
height of the mounted fixture: Carefully pull cord up into
canopy to shorten the height of fixture or carefully pull cord
down to lengthen the height of fixture. When desired height
is achieved, tighten threaded stud on strain relief. Tie cord
protruding from inside canopy in knot and tighten knot
securely.
3) TURN OFF POWER.
IMPORTANT: Before you start, NEVER attempt any work
without shutting off the electricity until the work is done.
a) Go to the main fuse, or circuit breaker, box in your
home. Place the main power switch in the “OFF” position.
b) Unscrew the fuse(s), or switch “OFF” the circuit breaker
switch(s), that control the power to the fixture or room
that you are working on.
c) Place the wall switch in the “OFF” position. If the fixture
to be replaced has a switch or pull chain, place those in
the “OFF” position.
4) Find the appropriate threaded holes on mounting strap.
Assemble mounting screws into threaded holes.
5) Attach mounting strap to outlet box. (Screws not provided).
Mounting strap can be adjusted to suit position of fixture.
6) Grounding instructions: (See Illus. A or B).
A) On fixtures where mounting strap is provided with a
hole and two raised dimples. Wrap ground wire from
outlet box around green ground screw, and thread into hole.
B) On fixtures where a cupped washer is provided. Attach
ground wire from outlet box under cupped washer and
green ground screw, and thread into mounting strap.
If fixture is provided with ground wire. Connect fixture
ground wire to outlet box ground wire with wire connector.
(Not provided.) After following the above steps. Never
connect ground wire to black or white power supply wires.
7) Make wire connections (connectors not provided.) Reference
chart below for correct connections and wire accordingly.
8) Push fixture to ceiling, carefully passing mounting screws
through holes in canopy.
9) Thread knurl knobs onto mounting screws. Tighten knurl
knobs to secure fixture to ceiling.
10) Raise outer glass shade up to fixture. Pass hole in outer
glass shade over socket.
11) Slip spacer over socket inside outer glass shade.
12) Raise inner glass shade up to fixture. Pass hole in inner
glass shade over socket.
13) Thread socket ring onto socket. Tighten socket ring to
secure glass in place. (DO NOT over tighten.)
GREEN GROUND
SCREW
CUPPED
WASHER
A
B
OUTLET BOX
GROUND
FIXTURE
GROUND
DIMPLES
WIRE CONNECTOR
(NOT PROVIDED)
OUTLET BOX
GROUND
GREEN GROUND
SCREW
FIXTURE
GROUND
Connect Black or
Red Supply Wire to:
Connect
White Supply Wire to:
Black White
*Parallel cord (round & smooth) *Parallel cord (square & ridged)
Clear, Brown, Gold or Black
without tracer
Clear, Brown, Gold or Black
with tracer
Insulated wire (other than green)
with copper conductor
Insulated wire (other than green)
with silver conductor
*Note: When parallel wires (SPT I & SPT II)
are used. The neutral wire is square shaped
or ridged and the other wire will be round in
shape or smooth (see illus.)
Neutral Wire
Date Issued: 10/17/14
IS-43629-US
CANOPY
ESCUDETE
KNURL KNOB
PERILLA ESTRADA
SEE OTHER SIDE FOR SPANISH TRANSLATIONS.
VEA EL OTRO LADO DE TRADUCCIONES AL ESPAÑOL.
We’re here to help 866-558-5706
Hrs: M-F 9am to 5pm EST
OUTER GLASS SHADE
VIDRIO EXTERIOR
PANTALLA
KNOT
NUDO
THREADED STUD
ESPÁRRAGO
ROSCADO
SOCKET RING
ANILLO DEL CASQUILLO
CORD
CORDÓN
STRAIN RELIEF
ALIVIO DE LA TENSIÓN
SPACER
ESPACIADOR
INNER GLASS SHADE
VIDRIO INTERIOR
PANTALLA
SOCKET
CASQUILLO
(1 pages)
(2 pages)
Manymanuals.com
Manymanuals.de
Manymanuals.fr
Manymanuals.it
Manymanuals.pl
Manymanuals.cz
Manymanuals.es
Manymanuals-pt.com
Comments to this Manuals