Kichler 12353BK v.1 User Manual download pdf

KICHLER

LED UNDERCABINET MOUNT POWER SUPPLY

INSTALLATION INSTRUCTIONS

P/N: 12353BK, 12353WH

NOTE: All installations should comply with national and

local electrical codes. If you have any doubts concerning

installation contact a qualiﬁed licensed electrician.

IMPORTANT SAFETY INSTRUCTIONS

A) Read all instructions.

B) Do not conceal or extend exposed conductors through a

building wall.

C) Do not install this system in wet locations.

D) For low voltage exposed insulated conductor systems required

by 30.1(c) do not install any part of this system less than 7

feet (2.2 m) above the ﬂoor.

E) To reduce the risk of ﬁre and burns, do not install this lighting

system where the exposed bare conductors can be shorted

or contact any conductive materials.

F) To reduce the risk of ﬁre and overheating, make sure all

connections are tight.

G) Do not install any luminaire closer than 6 inches (15.25 cm)

from any curtain, or similar combustible materials.

H) Turn off electrical power before modifying the lighting system

in any way.

SAVE THESE INSTRUCTIONS

1. On the tall side of wire module there are two gates. Feed a

minimum of 4” (10.2 cm) of Type NM non-metallic sheathed

cable (12-2 with ground or 14-2 with ground) through the gate.

Trim cable to 4” (10.2 cm) if necessary .

NOTE: These gates serve as strain reliefs holding cable

securely in place. Gates should not be removed and no more

then one cable should pass through each.

2. Peel back and remove outer jacket on cable to approximately

½” (1.3 cm) of inside of gate. (See Fig. 1)

3. Strip approximately ½” (1.3 cm) of insulation off each black

and white wire.

NOTE: On inside of wire module cover is a gage to assist in

stripping the correct amount of insulation. (See Fig 2)

4. Position the housing against the back of the cabinet and fasten

the housing to the mounting surface using the captive screws.

(See Fig. 3 and 4)

NOTE: DO NOT OVER TIGHTEN SCREW.

5. Use pliers to push stripped wires into the appropriate connectors.

Careful not to cut insulation. (See Fig. 5)

NOTE: The push-in connectors are surrounded by color

coded rings, indicating which wire to install.

  • blackwiretoblackringconnector

  • whitewiretowhiteringconnector

NOTE: To remove the wires from the connectors, trim wires

close to connector. Grip the trimmed stub with pliers and

twist while pulling out ward.

6. Push the un-insulated ground wire(s) into the provided, loose

splicing connector. (See Fig. 5)

7. Slightly tug on each wire to ensure connection has been

made and is secure.

8. Install wire module cover over exposed wires by aligning

the front tabs with the slots in the housing and snapping cover

into place. Firmly fasten the cover to the housing by using the

included screw. (See Fig. 6)

NOTE: DO NOT OVER TIGHTEN SCREW.

9. At this time proceed to LED ﬁxture installation following

instructions provided with ﬁxture.

10. To remove cover, remove center screw then slide screwdriver

into slot formed by cover and wire module then pull screw

driver handle away from wire module until cover separates

from wire module.

Date Issued: 12/5/08 IS-12353-CB

1/2"

FIG. 1

FIG. 2

FIG. 3

50W POWER SUPPLY

PRE-INSTALLED SCREW

FIG. 4

SPLICING CONNECTOR

BLACK WIRE

BLACK RING

CONNECTOR

WHITE WIRE

WHITE RING

CONNECTOR

GROUND WIRE

SLOTS IN

HOUSING

TABS ON COVER

SCREW

FIG. 6

FIG. 5

FROM SWITCH OR

MAIN BREAKER

TO NEXT RUN OR

CABINET

INSTRUCTIONS

For Assembling and Installing Fixtures in Canada

Pour L’assemblage et L’installation Au Canada

Summary of Contents

Page 1

KICHLER® LED UNDERCABINET MOUNT POWER SUPPLY INSTALLATION INSTRUCTIONSP/N: 12353BK, 12353WHNOTE: All installations should comply with national and loc

Related models: 12353WH v.1 | 12353BK v.2 | 12353WH v.2 |

Comments to this Manuals

No comments

Kichler 12353BK v.1 User Manual

Browse online or download User Manual for Hardware Kichler 12353BK v.1. Kichler 12353BK v.1 User Manual

Summary of Contents

Related models: 12353WH v.1 | 12353BK v.2 | 12353WH v.2 |

Comments to this Manuals

Related products and manuals for Hardware Kichler 12353BK v.1