Kichler 15861 User Manual download pdf

FOR USE WITH LANDSCAPE LIGHTING SYSTEMS ONLY.

1) The device is accepted as a component of a landscape lighting system

where the suitability of the CSA or UL labeled combination shall be deter

mined by CSA, UL respectively or the local inspection authorities having

jurisdiction.

2) Fixture shall be connected to an extra low voltage transformer approved for

use with landscape lighting systems.

3) This ﬁxture is to be connected to a secondary wiring of the following type:

12 GA 60°C minimum type;

SPT-3 suitable for outdoor use; or

approved landscape lighting cable.

INSTRUCTIONS PERTAINING TO A RISK OF FIRE,OR INJURY

TO PERSONS

IMPORTANT SAFETY INSTRUCTIONS

Lighted lamp is HOT!

WARNING — To reduce the risk of FIRE OR INJURY TO PERSONS.

1) Turn off / unplug and allow to cool before replacing lamp.

2) Lamp gets HOT quickly! Contact only switch / plug when turning on.

3) Do not touch hot lens or cowl.

4) Do not remain in light if skin feels warm. (Light is intense, it may cause

“sunburn”.)

5) Do not look directly at lighted lamp.

6) Keep lamp away from materials that may burn.

7) Use only with wattage and lamp marked on ﬁxture.

8) Do not touch the inner glass envelope of the lamp at any time. Use a soft

cloth. Oil from skin may damage lamp.

9) Do not operate the ﬁxture with a damaged or missing lens.

CAUTION

WHEN INSTALLING KICHLER LANDSCAPE LIGHTING (LINE VOLTAGE OR LOW

VOLTAGE), CARE SHOULD BE TAKEN TO KEEP CLEAR OF POTENTIALLY COMBUS-

TIBLE MATERIALS.

WHEN MAINTAINING THE FIXTURES, BE SURE TO REMOVE LEAVES, PINE NEEDLES,

GRASS CLIPPINGS, MULCH, OR ANY DEBRIS THAT HAS ACCUMULATED ON THE

LIGHT BULB, LENS, OR BODY OF THE FIXTURE.

ASSEMBLY AND INSTALLATION

1) Determine desired location for mounting ﬁxture.

2) At desired location, hammer stake (A) into ground. To avoid damage to

stake, place a board on top of stake while hammering. If ground is hard

and stake is difﬁcult to install, make a crosscut in ground using a ﬂat shovel.

3) Clear away area in ground at wireway slot (B) in top of stake (A). Lay 12V

cable into wireway slot (B) and screw stem (C) into stake (A). If assembly

does not look straight, adjust by pushing or pulling on stake only.

4) TURN OFF POWER.

5) Make wire connections using supplied Quic Disc

™

following instructions

below, or using other approved wiring connection method (not supplied.)

6) Adjust angle of ﬁxture body by loosening screw (D) at center of swivel (E).

7) The light is factory set to the high position. If you wish to set the light to

the low position remove thumbscrews (G) and diffuser (H) and set high/low

switch (F) to low setting. After switch is set reassemble diffuser to lamp

head using thumb screws.

Date Issued: 4/23/10 IS-15861-CB

OUTDOOR USE ONLY

DOM ETRE INSTALLE A L’EXTERIEUR

INSTRUCTIONS

For Assembling and Installing Fixtures in Canada

Pour L’assemblage et L’installation Au Canada

WARRANTY

WE WARRANT THE LANDSCAPE PRODUCTS FEATURED IN OUR LANDSCAPE LIGHTING CATALOG (WITH THE EXCEPTION OF LIGHT BULBS) FOR FIVE YEARS AGAINST DEFECTS IN

MATERIALS AND WORKMANSHIP IF IT WAS PROPERLY INSTALLED AND FAILED UNDER NORMAL OPERATING CONDITIONS, PROVIDED IT IS RETURNED TO THE POINT OF PURCHASE,

WHERE IT WILL BE REPAIRED OR, AS IT MAY BE DETERMINED, TO REPLACE THE LANDSCAPE PRODUCT OR PARTS USED ON THAT PRODUCT.

QUIC DISC

™

WIRING INSTRUCTIONS

Turn off power.

The full length of the 18 GA ﬁxture wire may be used to connect with the 10 GA or 12 GA cable provided the following conditions are met:

• Wiring is to be protected by routing close to the xture or accessory or secured to a building structure such as house or deck.

• 18 GA xture wiring is to be cut off so that it is attached to the connector within 6 inches of the xture or building structure.

• If it is necessary to make the connections underground, then no more than 6 inches of the 18 GA xture wire is to be buried.

The Quic Disc

™

connector is designed to install one ﬁxture and accommodates one 18 GA ﬁxture wire and one 10 GA or one 12 GA supply wire.

Place the 10 gauge supply wire across the area marked 10 GA on Quic Disc

™

or place the 12 gauge supply wire across the area marked 12 GA

on Quic Disc

™

Place the 18 gauge ﬁxture wire across the area marked 18 GA on the Quic Disc

™

. After the wires are in place, connecta the top of the Quic

Disc

™

to the base with supplied screw, making sure that the wires remain ﬂat in the bottom portion of the Quic Disc

™

, and the screw is tightened

all the way down.

The copper contacts will automatically pierce the wires’ insulation. Excess 18 GA ﬁxture wire that sticks out the end of the Quic Disc

™

is to be cut off.

Make no other wiring connections to the 18 GA ﬁxture wire.

1 2

Summary of Contents

Page 1 - Lighted lamp is HOT!

FOR USE WITH LANDSCAPE LIGHTING SYSTEMS ONLY.1) The device is accepted as a component of a landscape lighting system where the suitability of the C

Page 2 - INSTRUCTIONS

A UTILISER UNIQUEMENT POUR LES SYSTÈMES D’ÉCLAIRAG PAYSAGER1) Le dispositif est accepté en tant que composant d’un système d’é clairage paysager lor

Kichler 15861 User Manual

Browse online or download User Manual for Lighting Kichler 15861. Kichler 15861 Manuel d'utilisation

Summary of Contents

More documents for Lighting Kichler 15861

Comments to this Manuals

Kichler 15861 User Manual

Browse online or download User Manual for Lighting Kichler 15861. Kichler 15861 Manuel d'utilisation

Summary of Contents

More documents for Lighting Kichler 15861

Comments to this Manuals

Related products and manuals for Lighting Kichler 15861