Kichler 15093 User Manual download pdf

INSTRUCTIONS PERTAINING TO A RISK OF FIRE,OR INJURY TO

PERSONS

IMPORTANT SAFETY INSTRUCTIONS

Lighted lamp is HOT!

WARNING — To reduce the risk of FIRE OR INJURY TO PERSONS.

1) Turn off / unplug and allow to cool before replacing lamp.

2) Lamp gets HOT quickly! Contact only switch / plug when turning on.

3) Do not touch hot lens or cowl.

4) Do not remain in light if skin feels warm. (Light is intense, it may cause

“sunburn”.)

5) Do not look directly at lighted lamp.

6) Keep lamp away from materials that may burn.

7) Useonlywithwattageandlampmarkedonxture.

8) Do not touch the inner glass envelope of the lamp at any time. Use a soft cloth.

Oil from skin may damage lamp.

9) Donotoperatethexturewithadamagedormissinglens.

FOR USE WITH LANDSCAPE LIGHTING SYSTEMS ONLY.

1) The device is accepted as a component of a landscape lighting system

where the suitability of the CSA or UL labeled combination shall be deter

mined by CSA, UL respectively or the local inspection authorities having

jurisdiction.

2) Fixtureshallbeconnectedtoanextralowvoltagetransformerapproved

for use with landscape lighting systems.

3) Thisxtureistobeconnectedtoasecondarywiringofthefollowingtype:

12 GA 60°C minimum type;

SPT-3 suitable for outdoor use; or

approved landscape lighting cable.

CAUTION

WHEN INSTALLING KICHLER LANDSCAPE LIGHTING (LINE VOLTAGE OR LOW VOLTAGE),

CARE SHOULD BE TAKEN TO KEEP CLEAR OF POTENTIALLY COMBUSTIBLE MATERIALS.

WHEN MAINTAINING THE FIXTURES, BE SURE TO REMOVE LEAVES, PINE NEEDLES,

GRASS CLIPPINGS, MULCH, OR ANY DEBRIS THAT HAS ACCUMULATED ON THE LIGHT

BULB, LENS, OR BODY OF THE FIXTURE.

ACCENT LIGHT ASSEMBLY -

FIXTURE IS SUITABLE FOR OUTDOOR USE ONLY

NOTE:Cablesuppliedwithxtureisnottoberunthroughwall.Reference

local electrial codes if this type of installation is required.

1) Screw accent light into mounting plate. Secure in place with locknut.

2) Securexturetomountingsurfaceoroutletboxusinggasketandthe

appropriate screws (provided).

3) Slip O-ring over accent body and into O-ring groove closest to center of

accent body.

4) Slip second O-ring into O-ring groove farthest from center of accent body.

5) Install lamp (not supplied) into socket inside accent light.

NOTE: Use caution when assembling. Hold lamp by outer housing.

DO NOT touch glass envelope inside. If this happens, clean bulb with

denatured alcohol and a lint free cloth.

6) Assemble cowl with screen to accent body. Secure in place using either

the provided thumb screw or vandal resistant screw. NOTE: Vandal

 resistantscrewsrequiresa3/32hexkey(notprovided)forinstallationor

removal.

7) Make wire connections using supplied Quic Disc

™

following instructions

below, or using other approved wiring connection method (not supplied.)

DateIssued:12/2/11 IS-15093-CB

OUTDOOR USE ONLY

DOM ETRE INSTALLE A L’EXTERIEUR

INSTRUCTIONS

For Assembling and Installing Fixtures in Canada

Pour L’assemblage et L’installation Au Canada

For warranty information please visit: http://www.landscapelighting.com/portal/warranty_page

Pour de plus amples informations sur la garantie, cliquez sur le lien ci-dessous : http://www.landscapelighting.com/portal/warranty_page

QUIC DISC

™

WIRING INSTRUCTIONS

Turn off power.

Thefulllengthofthe18GAxturewiremaybeusedtoconnectwiththe10GAor12GAcableprovidedthefollowingconditionsaremet:

•Wiringistobeprotectedbyroutingclosetothextureoraccessoryorsecuredtoabuildingstructuresuchashouseordeck.

• 18GAxturewiringistobecutoffsothatitisattachedtotheconnectorwithin6inchesofthextureorbuildingstructure.

• Ifitisnecessarytomaketheconnectionsunderground,thennomorethan6inchesofthe18GAxturewireistobeburied.

The Quic Disc

™

connector is designed to install onextureandaccommodatesone18GAxturewireandone 10 GA or one 12 GA supply wire.

Place the 10 gauge supply wire across the area marked 10 GA on Quic Disc

™

or place the 12 gauge supply wire across the area marked 12 GA

on Quic Disc

™

Placethe18gaugexturewireacrosstheareamarked18GAontheQuicDisc

™

. After the wires are in place, connecta the top of the Quic

Disc

™

tothebasewithsuppliedscrew,makingsurethatthewiresremainatinthebottomportionoftheQuicDisc

™

, and the screw is tightened

all the way down.

Thecoppercontactswillautomaticallypiercethewires’insulation.Excess18GAxturewirethatsticksouttheendoftheQuicDisc

™

is to be cut off.

Makenootherwiringconnectionstothe18GAxturewire.

OUTLET BOX

BO´ITEDESORTIE

DECOURANT

LOCKNUT

CONTRE-ECROU

ACCENT LIGHT

ÉCLAIRAGED’APPOINT

O-RING

JOINTTORIQUE

THUMBSCREW

VIS A AILETTES

COWL

CAPOT

GASKET

JOINT

MOUNTING PLATE

PLAQUE E MONTAGE

INCORRECT

MAUVAISE

POSITION

CORRECT

BONNE POSITION

1 2

Summary of Contents

Page 1 - Lighted lamp is HOT!

INSTRUCTIONS PERTAINING TO A RISK OF FIRE,OR INJURY TO PERSONSIMPORTANT SAFETY INSTRUCTIONSLighted lamp is HOT!WARNING — To reduce the risk of FIRE OR

Page 2 - OUDEBLESSURE

INSTRUCTIONSPOUREVITERTOUTRISQUED’INCENDIEOUDEBLESSUREINSTRUCTIONS DE SECURITE IMPORTANTESUne lampe allumée est BRULANTE!AVERTISSEMENT — Pour

Kichler 15093 User Manual

Browse online or download User Manual for Lighting Kichler 15093. Kichler 15093 Manuel d'utilisation

Summary of Contents

More documents for Lighting Kichler 15093

Comments to this Manuals

Kichler 15093 User Manual

Browse online or download User Manual for Lighting Kichler 15093. Kichler 15093 Manuel d'utilisation

Summary of Contents

More documents for Lighting Kichler 15093

Comments to this Manuals

Related products and manuals for Lighting Kichler 15093