Kichler 43468 User Manual download pdf

1) Pass ﬁxture wire through center stem. Screw center stem to

top of ﬁxture body.

2) Align hole in bottom of side bracket with hole in bottom of

center trim.

3) Thread screw into hole in bottom of side bracket and into

hole in bottom of center trim.

4) Slip hole in small trim ring over top end of center stem.

5) Align hole in center trim ring with hole in top of side bracket.

6) Thread end of ball stud through hole in top of side bracket

and into hole in side of center trim ring.

7) Repeat steps 2 - 6 for remaining side brackets.

8) Tighten ball studs and screws after all side brackets have

been installed.

9) Pass ﬁxture wire through coupling. Screw coupling onto top

of center stem.

10) Thread loop onto coupling on top of center stem.

11) TURN OFF POWER.

IMPORTANT: Before you start, NEVER attempt any work

without shutting off the electricity until the work is done.

a) Go to the main fuse, or circuit breaker, box in your

home. Place the main power switch in the “OFF”

position.

b) Unscrew the fuse(s), or switch “OFF” the circuit breaker

switch(s), that control the power to the ﬁxture or room

that you are working on.

c) Place the wall switch in the “OFF” position. If the ﬁxture

to be replaced has a switch or pull chain, place those in

the “OFF” position.

12) Take threaded pipe from parts bag and screw in screw collar

loop a minimum of 6 mm (1/4”). Lock into place with hexnut.

13) Run another hexnut down threaded pipe almost touching

ﬁrst hexnut. Now screw threaded pipe into mounting strap.

Mounting strap must be positioned with extruded thread

faced into outlet box. Threaded pipe must protrude out the

back of mounting strap. Screw third hexnut onto end of

threaded pipe protruding from back of mounting strap.

14) Connect mounting strap to outlet box.

15) Unscrew the threaded ring from screw collar loop. Take

canopy and pass over screw collar loop. Approximately one

half of the screw collar loop exterior threads should be

exposed. Adjust screw collar loop by turning assembly up or

down in mounting strap. Remove canopy.

16) After desired position is found, tighten both top and bottom

hexnuts up against the bottom and top of the mounting

strap.

17) Slip canopy over screw collar loop and thread on threaded

ring. Attach chain (with ﬁxture connected) to bottom of

screw collar loop. Unscrew threaded ring, let canopy and

threaded ring slip down.

18) Weave electrical wire and ground wire through chain links no

more than 3 inches apart. Pass wire through threaded ring,

canopy, screw collar loop, threaded pipe and into outlet box.

19) Connect ﬁxture ground wire to outlet box ground wire with

wire connector. (Not provided.) Never connect ground wire

to black or white power supply wire.

20) Make wire connections (connectors not provided). Reference

chart below for correct connections and wire accordingly.

21) Raise canopy to ceiling.

22) Secure canopy in place by tightening threaded ring onto

screw collar loop.

Date Issued: 8/9/13 IS-43468-CB

Connect Black or

Red Supply Wire to:

Connect

White Supply Wire to:

Black White

*Parallel cord (round & smooth) *Parallel cord (square & ridged)

Clear, Brown, Gold or Black

without tracer

Clear, Brown, Gold or Black

with tracer

Insulated wire (other than green)

with copper conductor

Insulated wire (other than green)

with silver conductor

*Note: When parallel wires (SPT I & SPT II)

are used. The neutral wire is square shaped

or ridged and the other wire will be round in

shape or smooth (see illus.)

Neutral Wire

INSTRUCTIONS

For Assembling and Installing Fixtures in Canada

Pour L’assemblage et L’installation Au Canada

SEE OTHER SIDE FOR CANADIAN FRENCH TRANS-

LATIONS.

VOIR L’AUTRE CÔTÉ POUR LES CANADIENS TRA-

DUCTIONS EN FRANÇAIS.

MOUNTING STRAP

PATTE DE FIXATION

HEXNUT

ECROU HEXAGONAL

THREADED PIPE

TUBE FILETÉ

SCREW COLLAR LOOP

COLLIER-ÉCROU

CANOPY

CACHE THREADED RING

BAGUE FILETÉE

LOOP

BOUCLE

CENTER STEM

TIGE CENTTRALE

COUPLING

COUPLAGE

CENTER TRIM RING

ANNEAU DE LA GARNITURE

SIDE BRACKET

SUPPORT LATÉRAL

CENTER TRIM

GARNITURE CENTRALE

ARM

BRAS

BALL STUD

GOUJON À BILLE

SCREW

VIS

1 2

LATIONS 1
DUCTIONS EN FRANÇAIS 1

Summary of Contents

Page 1 - DUCTIONS EN FRANÇAIS

1) Pass ﬁxture wire through center stem. Screw center stem to top of ﬁxture body.2) Align hole in bottom of side bracket with hole in bottom of

Page 2

1) Passer le ﬁl du luminaire par la tige centrale. Visser la tige centrale en haut du luminaire.2) Aligner le trou dans le bas du support latéral

Comments to this Manuals

No comments

Kichler 43468 User Manual

Browse online or download User Manual for Lighting Kichler 43468. Kichler 43468 Manuel d'utilisation

Summary of Contents

Comments to this Manuals

Related products and manuals for Lighting Kichler 43468