Kichler 15861 User Manual

Browse online or download User Manual for Lighting Kichler 15861. Kichler 15861 User Manual

  • Download
  • Add to my manuals
  • Print
  • Page
    / 2
  • Table of contents
  • BOOKMARKS
  • Rated. / 5. Based on customer reviews
Page view 0
SAFETY INSTRUCTIONS
READ THIS FIRST
KEEP THESE INSTRUCTIONS
This fixture is intended for installation in accordance with the National
Electric Code (NEC) and Local code specifications. Failure to adhere to
these codes and instructions may result in serious injury and/or property
damage and will void the warranty.
1) WARNING: This fixture is not to be installed within 10 feet (3M) of a pool,
spa or fountain.
2) This fixture is to be used only with a power unit (transformer) rated a
maximum of 300 W (25 AMPS) 15 volts.
3) The #18 ga. fixture wire is not intended for direct burial.
4) Direct burial rated wire is to be buried a minimum of 6” (152mm) beneath
the surface of the ground.
NOTE: If additional Direct Burial wire is needed, contact your local Kichler
®
landscape distributor.
•8GAwirecanbepurchasedinlengthof250’(76M),15503-BK.
•10GAwirecanbepurchasedinlengthof250’(76M),15504-BK.
•12GAwirecanbepurchasedinlengthsof100’(30M),15501-BK;250’
(76M),15502-BK;500’(152M),15505-BK;and1000’(304M),15506-BK.
5) Fixture shall not use a tungsten halogen lamp unless the fixture is marked
for use with such lamps.
6) Wiring connections must be made with approved/listed wire connection
device(s)suitablefortheapplication.Donotexceedmanufacturers’wiring
combination specifications for size and quantity of conductors.
INSTRUCTIONS PERTAINING TO A RISK OF FIRE, OR INJURY
TO PERSONS
IMPORTANT SAFETY INSTRUCTIONS
Lighted lamp is HOT!
WARNING — To reduce the risk of FIRE OR INJURY TO PERSONS.
1) Turn off / unplug and allow to cool before replacing lamp.
2) Lamp gets HOT quickly! Contact only switch / plug when turning on.
3) Do not touch hot lens or cowl.
4) Do not remain in light if skin feels warm. (Light is intense, it may cause
“sunburn”.)
5) Do not look directly at lighted lamp.
6) Keep lamp away from materials that may burn.
7) Useonlywithwattageandlampmarkedonxture.
8) Donottouchtheinnerglassenvelopeofthelampatanytime.Useasoft
cloth. Oil from skin may damage lamp.
9) Do not operate the fixture with a damaged or missing lens.
CAUTION
WHEN INSTALLING KICHLER LANDSCAPE LIGHTING (LINE VOLTAGE OR LOW
VOLTAGE), CARE SHOULD BE TAKEN TO KEEP CLEAR OF POTENTIALLY COMBUS-
TIBLE MATERIALS.
WHEN MAINTAINING THE FIXTURES, BE SURE TO REMOVE LEAVES, PINE NEEDLES,
GRASS CLIPPINGS, MULCH, OR ANY DEBRIS THAT HAS ACCUMULATED ON THE
LIGHT BULB, LENS, OR BODY OF THE FIXTURE.
ASSEMBLY AND INSTALLATION
1) Determine desired location for mounting fixture.
2) At desired location, hammer stake (A) into ground. To avoid damage to
stake, place a board on top of stake while hammering. If ground is hard
and stake is difficult to install, make a crosscut in ground using a flat shovel.
3) Clear away area in ground at wireway slot (B) in top of stake (A). Lay 12V
cable into wireway slot (B) and screw stem (C) into stake (A). If assembly
does not look straight, adjust by pushing or pulling on stake only.
4) TURNOFFPOWER.
5) Make wire connections using supplied Quic Disc
following instructions
below, or using other approved wiring connection method (not supplied.)
6) Adjustangleofxturebodybylooseningscrew(D)atcenterofswivel(E).
7) Thelightisfactorysettothehighposition.Ifyouwishtosetthelightto
thelowpositionremovethumbscrews(G)anddiffuser(H)andsethigh/low
switch (F) to low setting. After switch is set reassemble diffuser to lamp
head using thumb screws.
WARRANTY
WE WARRANT THE LANDSCAPE PRODUCTS FEATURED IN OUR LANDSCAPE LIGHTING CATALOG (WITH THE EXCEPTION OF LIGHT BULBS) FOR FIVE YEARS AGAINST DEFECTS IN
MATERIALS AND WORKMANSHIP IF IT WAS PROPERLY INSTALLED AND FAILED UNDER NORMAL OPERATING CONDITIONS, PROVIDED IT IS RETURNED TO THE POINT OF PURCHASE,
WHERE IT WILL BE REPAIRED OR, AS IT MAY BE DETERMINED, TO REPLACE THE LANDSCAPE PRODUCT OR PARTS USED ON THAT PRODUCT.
Date Issued: 4/23/10 IS-15861-US
QUIC DISC
WIRING INSTRUCTIONS
Turn off power.
Thefulllengthofthe18GAxturewiremaybeusedtoconnectwiththe10GAor12GAcableprovidedthefollowingconditionsaremet:
•Wiringistobeprotectedbyroutingclosetothextureoraccessoryorsecuredtoabuildingstructuresuchashouseordeck.
• 18GAxturewiringistobecutoffsothatitisattachedtotheconnectorwithin6inchesofthextureorbuildingstructure.
• Ifitisnecessarytomaketheconnectionsunderground,thennomorethan6inchesofthe18GAxturewireistobeburied.
The Quic Disc
connector is designed to install one fixture and accommodates one18GAxturewireandone10GAorone12GAsupplywire.
Placethe10gaugesupplywireacrosstheareamarked10GAonQuicDisc
orplacethe12gaugesupplywireacrosstheareamarked12GA
on Quic Disc
.
Placethe18gaugexturewireacrosstheareamarked18GAontheQuicDisc
. After the wires are in place, connecta the top of the Quic
Disc
to the base with supplied screw, making sure that the wires remain flat in the bottom portion of the Quic Disc
, and the screw is tightened
all the way down.
Thecoppercontactswillautomaticallypiercethewires’insulation.Excess18GAxturewirethatsticksouttheendoftheQuicDisc
is to be cut off.
Makenootherwiringconnectionstothe18GAxturewire.
A
B
C
E
D
G
H
F
Page view 0
1 2

Summary of Contents

Page 1 - Lighted lamp is HOT!

SAFETY INSTRUCTIONSREAD THIS FIRSTKEEP THESE INSTRUCTIONSThis fixture is intended for installation in accordance with the National Electric Code (NEC)

Page 2 - LESION A LAS PERSONAS

INSTRUCCIONES DE SEGURIDADPRIMERO LEA ESTOGUARDE ESTAS INSTRUCCIONESEste artefacto se debe instalar de acuerdo con el Código Eléctrico Nacional (NEC,

Comments to this Manuals

No comments