Kichler 15390 User Manual Page 1

Browse online or download User Manual for Lighting Kichler 15390. Kichler 15390 User Manual

  • Download
  • Add to my manuals
  • Print
  • Page
    / 2
  • Table of contents
  • BOOKMARKS
  • Rated. / 5. Based on customer reviews
Page view 0
SAFETY INSTRUCTIONS
READ THIS FIRST
KEEP THESE INSTRUCTIONS
This xture is intended for installation in accordance with the National
Electric Code (NEC) and Local code specications. Failure to adhere to
these codes and instructions may result in serious injury and/or property
damage and will void the warranty.
1) WARNING: This xture is not to be installed within 10 feet (3M) of a pool,
spa or fountain.
2) This xture is to be used only with a power unit (transformer) rated a
maximum of 300 W (25 AMPS) 15 volts.
3) The #18 ga. xture wire is not intended for direct burial.
4) Direct burial rated wire is to be buried a minimum of 6” (152mm) beneath
the surface of the ground.
NOTE: If additional Direct Burial wire is needed, contact your local Kichler
®
landscape distributor.
• 8 GA wire can be purchased in length of 250’ (76 M), 15503-BK.
• 10 GA wire can be purchased in length of 250’ (76 M), 15504-BK.
• 12 GA wire can be purchased in lengths of 100’ (30 M), 15501-BK; 250’
(76 M), 15502-BK; 500’ (152M), 15505-BK; and 1000’ (304 M), 15506-BK.
5) Fixture shall not use a tungsten halogen lamp unless the xture is marked
for use with such lamps.
6) Wiring connections must be made with approved/listed wire connection
device(s) suitable for the application. Do not exceed manufacturers’ wiring
combination specications for size and quantity of conductors.
INSTRUCTIONS PERTAINING TO A RISK OF FIRE, OR INJURY TO
PERSONS
IMPORTANT SAFETY INSTRUCTIONS
Lighted lamp is HOT!
WARNING — To reduce the risk of FIRE OR INJURY TO PERSONS.
1) Turn off / unplug and allow to cool before replacing lamp.
2) Lamp gets HOT quickly! Contact only switch / plug when turning on.
3) Do not touch hot lens or cowl.
4) Do not remain in light if skin feels warm. (Light is intense, it may cause
“sunburn”.)
5) Do not look directly at lighted lamp.
6) Keep lamp away from materials that may burn.
7) Use only with wattage and lamp marked on xture.
8) Do not touch the inner glass envelope of the lamp at any time. Use a soft
cloth. Oil from skin may damage lamp.
9) Do not operate the xture with a damaged or missing lens.
CAUTION
WHEN INSTALLING KICHLER LANDSCAPE LIGHTING (LINE VOLTAGE OR LOW VOLTAGE),
CARE SHOULD BE TAKEN TO KEEP CLEAR OF POTENTIALLY COMBUSTIBLE MATERIALS.
WHEN MAINTAINING THE FIXTURES, BE SURE TO REMOVE LEAVES, PINE NEEDLES,
GRASS CLIPPINGS, MULCH, OR ANY DEBRIS THAT HAS ACCUMULATED ON THE LIGHT
BULB, LENS, OR BODY OF THE FIXTURE.
ASSEMBLY AND INSTALLATION
1) Determine desired location for mounting xture.
2) At desired location, hammer stake (A) into ground. To avoid damage to
stake, place a board on top of stake while hammering. If ground is hard
and stake is difcult to install, make a crosscut in ground using a at
shovel.
3) Clear away area in ground at wireway slot (B) in top of stake (A).
4) Make lamp connections. Slide spade lugs (C) beneath head of screws on
back of par 36 lamp (not supplied) and tighten screws to secure connection.
NOTE: To ease replacement of lamp and prevent corrosion of connection,
apply 15670, Corrosion Preventative Compound (sold separately) liberally
over spade lugs, par 36 screws and tabs.
5) Carefully place lamp inside cowl (E) and place o-ring (F) on lamp.
6) Align notch (G) in retaining ring with rib (H) inside cowl (E). This will align
screws (J) with holes.
7) Tighten screws (J).
8) Lay 12V cable into wireway slot (B) and screw xture into stake (A).
9) Once desired direction is achieved run locknut (K) down against stake (A).
10) Adjust angle of xture by loosening screw (L) in swivel (M).
11) TURN OFF POWER.
12) Make wire connections using supplied Quic Disc
following instructions
below, or using other approved wiring connection method (not supplied.)
Date Issued: 1/27/12 IS-15390-US
QUIC DISC
WIRING INSTRUCTIONS
Turn off power.
The full length of the 18 GA xture wire may be used to connect with the 10 GA or 12 GA cable provided the following conditions are met:
Wiring is to be protected by routing close to the xture or accessory or secured to a building structure such as house or deck.
18 GA xture wiring is to be cut off so that it is attached to the connector within 6 inches of the xture or building structure.
If it is necessary to make the connections underground, then no more than 6 inches of the 18 GA xture wire is to be buried.
The Quic Disc
connector is designed to install one xture and accommodates one 18 GA xture wire and one 10 GA or one 12 GA supply wire.
Place the 10 gauge supply wire across the area marked 10 GA on Quic Disc
or place the 12 gauge supply wire across the area marked 12 GA
on Quic Disc
.
Place the 18 gauge xture wire across the area marked 18 GA on the Quic Disc
. After the wires are in place, connecta the top of the Quic
Disc
to the base with supplied screw, making sure that the wires remain at in the bottom portion of the Quic Disc
, and the screw is tightened
all the way down.
The copper contacts will automatically pierce the wires’ insulation. Excess 18 GA xture wire that sticks out the end of the Quic Disc
is to be cut off.
Make no other wiring connections to the 18 GA xture wire.
D
E
H
B
A
G
F
L
K
M
C
For warranty information please visit: http://www.landscapelighting.com/portal/warranty_page
Para informacion de la garantia por favor visite: www.landscapelighting.com/portal/warranty_page
Page view 0
1 2

Summary of Contents

Page 1 - Lighted lamp is HOT!

SAFETY INSTRUCTIONSREAD THIS FIRSTKEEP THESE INSTRUCTIONSThis xture is intended for installation in accordance with the National Electric Code (NEC)

Page 2 - LESION A LAS PERSONAS

INSTRUCCIONES DE SEGURIDADPRIMERO LEA ESTOGUARDE ESTAS INSTRUCCIONESEste artefacto se debe instalar de acuerdo con el Código Eléctrico Nacional (NEC,

Comments to this Manuals

No comments