INSTRUCTIONS PERTAINING TO A RISK OF FIRE,OR INJURY TO
PERSONS
IMPORTANT SAFETY INSTRUCTIONS
Lighted lamp is HOT!
WARNING — To reduce the risk of FIRE OR INJURY TO PERSONS.
1) Turn off / unplug and allow to cool before replacing lamp.
2) Lamp gets HOT quickly! Contact only switch / plug when turning on.
3) Do not touch hot lens or cowl.
4) Do not remain in light if skin feels warm. (Light is intense, it may cause
“sunburn”.)
5) Do not look directly at lighted lamp.
6) Keep lamp away from materials that may burn.
7) Useonlywithwattageandlampmarkedonxture.
8) Do not touch the inner glass envelope of the lamp at any time. Use a soft cloth.
Oil from skin may damage lamp.
9) Donotoperatethexturewithadamagedormissinglens.
FOR USE WITH LANDSCAPE LIGHTING SYSTEMS ONLY.
1) The device is accepted as a component of a landscape lighting system
where the suitability of the CSA or UL labeled combination shall be deter
mined by CSA, UL respectively or the local inspection authorities having
jurisdiction.
2) Fixtureshallbeconnectedtoanextralowvoltagetransformerapproved
for use with landscape lighting systems.
3) Thisxtureistobeconnectedtoasecondarywiringofthefollowingtype:
12 GA 60°C minimum type;
SPT-3 suitable for outdoor use; or
approved landscape lighting cable.
CAUTION
WHEN INSTALLING KICHLER LANDSCAPE LIGHTING (LINE VOLTAGE OR LOW VOLTAGE),
CARE SHOULD BE TAKEN TO KEEP CLEAR OF POTENTIALLY COMBUSTIBLE MATERIALS.
WHEN MAINTAINING THE FIXTURES, BE SURE TO REMOVE LEAVES, PINE NEEDLES,
GRASS CLIPPINGS, MULCH, OR ANY DEBRIS THAT HAS ACCUMULATED ON THE LIGHT
BULB, LENS, OR BODY OF THE FIXTURE.
WELL / ACCENT LIGHT ASSEMBLY
FIXTURE IS SUITABLE FOR OUTDOOR USE ONLY
1) Well / accent light can be installed two different ways.
A) If accent light is to be used for direct uplighting, dig hole 15” deep.
B) If accent light is to be used for wall washing, dig hole 9-1/2” deep.
These dimension will make hole deep enough to accommodate sleeve
plus 6” of pea gravel to insure proper drainage.
2) Fill bottom of hole with 6” of pea gravel.
3) Set sleeve in hole.
A)Directuplighting:Angledenddown.(Notillustrated)
B)Wallwashing:Angledendup.(Illustrated)
4) Using denatured alcohol clean both sides of yoke where rubber pads are
to be taped. Denatured alcohol will remove any oil, dirt or residue that may
keep rubber pads from sticking.
5) Remove paper backing from rubber pads and stick to yoke.
6) Slip O-ring over accent body and into O-ring groove closest to center of
accent body.
7) Slip second O-ring into O-ring groove farthest from center of accent body.
8) Install MR16 lamp (not supplied) into socket inside accent body.
NOTE: Use caution when assembling. Hold lamp by outer housing.
DONOTtouchglassenvelopeinside.Ifthishappens,cleanbulbwith
denatured alcohol and a lint free cloth.
9) Assemble cowl with lens to accent body. Secure in place using either the
provided thumbscrew or the vandal resistant screw. NOTE: Vandal
resistantscrewrequiresa3/32hexkey(NotProvided)forinstallationor
removal.
10) Unscrew phillips head screws in yoke enough to slip cowl between rubber
pads.
11) Tighten phillips head screws until cowl is held securely in place.
12) Guide wire from accent body under bottom of sleeve and back up between
sleeve and soil.
13) Slip yoke hook over edge of sleeve to support accent light.
14) Fill gaps surrounding outside of sleeve with soil.
15) Make wire connections using supplied Quic Disc
™
following instructions
below, or using other approved wiring connection method (not supplied.)
DateIssued:12/2/11 IS-15092-CB
DOM ETRE INSTALLE A L’EXTERIEUR
INSTRUCTIONS
For Assembling and Installing Fixtures in Canada
Pour L’assemblage et L’installation Au Canada
For warranty information please visit: http://www.landscapelighting.com/portal/warranty_page
Pour de plus amples informations sur la garantie, cliquez sur le lien ci-dessous : http://www.landscapelighting.com/portal/warranty_page
QUIC DISC
™
WIRING INSTRUCTIONS
Turn off power.
Thefulllengthofthe18GAxturewiremaybeusedtoconnectwiththe10GAor12GAcableprovidedthefollowingconditionsaremet:
•Wiringistobeprotectedbyroutingclosetothextureoraccessoryorsecuredtoabuildingstructuresuchashouseordeck.
• 18GAxturewiringistobecutoffsothatitisattachedtotheconnectorwithin6inchesofthextureorbuildingstructure.
• Ifitisnecessarytomaketheconnectionsunderground,thennomorethan6inchesofthe18GAxturewireistobeburied.
The Quic Disc
™
connector is designed to install onextureandaccommodatesone18GAxturewireandone 10 GA or one 12 GA supply wire.
Place the 10 gauge supply wire across the area marked 10 GA on Quic Disc
™
or place the 12 gauge supply wire across the area marked 12 GA
on Quic Disc
™
.
Placethe18gaugexturewireacrosstheareamarked18GAontheQuicDisc
™
. After the wires are in place, connecta the top of the Quic
Disc
™
tothebasewithsuppliedscrew,makingsurethatthewiresremainatinthebottomportionoftheQuicDisc
™
, and the screw is tightened
all the way down.
Thecoppercontactswillautomaticallypiercethewires’insulation.Excess18GAxturewirethatsticksouttheendoftheQuicDisc
™
is to be cut off.
Makenootherwiringconnectionstothe18GAxturewire.
HOOK
CROCHET
YOKE
COLLET
RUBBER PAD
COUSSINETDE
CAOUTCHOUC
LENS
LENTILLE
COWL
CAPOT
THUMB SCREW
VIS A AILETTES
O-RING
JOINTTORIQUE
O-RINGGROOVE
RAINUREDUJOINT
TORIQUE
ACCENTBODY
CORPSD’ACCENT
SLEEVE
MANCHON
Comments to this Manuals