
SAFETY INSTRUCTIONS
READ THIS FIRST
KEEP THESE INSTRUCTIONS
This xture is intended for installation in accordance with the National
Electric Code (NEC) and Local code specications. Failure to adhere to
these codes and instructions may result in serious injury and/or property
damage and will void the warranty.
FOR USE WITH LANDSCAPE LIGHTING SYSTEMS ONLY.
1) The device is accepted as a component of a landscape lighting system
where the suitability of the CSA or UL labeled combination shall be
determined by CSA, UL respectively or the local inspection authorities
having jurisdiction.
2) Fixture shall be connected to an extra low voltage transformer approved
for use with landscape lighting systems.
3) Thisxtureistobeconnectedtoasecondarywiringofthefollowing
type:
12 GA 60°C minimum type;
SPT-3 suitable for outdoor use; or
approved landscape lighting cable.
WARNING – RISK OF ELECTRIC SHOCK
• Donotmountluminairewithin10feet(3m)ofaswimmingpool,spaor
fountain.
• ThisxtureistobeusedonlywithaKichler
®
low voltage lighting power
unit(transformer)ratedamaximum15volts,300Wpersecondary(25AMPS)
NOTE: IfadditionalDirectBurialwireisneeded,contactyourlocalKichler
®
landscape distributor.
•8GAwirecanbepurchasedinlengthof250’(76M),15503-BK.
•10GAwirecanbepurchasedinlengthof250’(76M),15504-BK.
•12GAwirecanbepurchasedinlengthsof100’(30M),15501-BK;250’
(76M),15502-BK;500’(152M),15505-BK;and1000’(304M),15506-BK.
DateIssued:1/13/12 IS-16030-CB
OUTDOOR USE ONLY
DOM ETRE INSTALLE A L’EXTERIEUR
For Assembling and Installing Fixtures in Canada
Pour L’assemblage et L’installation Au Canada
QUIC DISC
™
WIRING INSTRUCTIONS
Turn off power.
Thefulllengthofthe18GAxturewiremaybeusedtoconnectwiththe10GAor12GAcableprovidedthefollowingconditionsaremet:
•Wiringistobeprotectedbyroutingclosetothextureoraccessoryorsecuredtoabuildingstructuresuchashouseordeck.
• 18GAxturewiringistobecutoffsothatitisattachedtotheconnectorwithin6inchesofthextureorbuildingstructure.
• Ifitisnecessarytomaketheconnectionsunderground,thennomorethan6inchesofthe18GAxturewireistobeburied.
TheQuicDisc
™
connector is designed to install onextureandaccommodatesone18GAxturewireandone 10 GA or one 12 GA supply wire.
Placethe10gaugesupplywireacrosstheareamarked10GAonQuicDisc
™
orplacethe12gaugesupplywireacrosstheareamarked12GA
onQuicDisc
™
.
Placethe18gaugexturewireacrosstheareamarked18GAontheQuicDisc
™
. After the wires are in place, connecta the top of the Quic
Disc
™
tothebasewithsuppliedscrew,makingsurethatthewiresremainatinthebottomportionoftheQuicDisc
™
, and the screw is tightened
all the way down.
Thecoppercontactswillautomaticallypiercethewires’insulation.Excess18GAxturewirethatsticksouttheendoftheQuicDisc
™
is to be cut off.
Makenootherwiringconnectionstothe18GAxturewire.
For warranty information please visit: http://www.landscapelighting.com/portal/warranty_page
Pour de plus amples informations sur la garantie, cliquez sur le lien ci-dessous : http://www.landscapelighting.com/portal/warranty_page
FIXTURE ASSEMBLY AND INSTALLATION
1. Turn off power.
2. Determineddesiredlocationofxtureanddighole.Holeshouldbe9”
(diameter)x6”(deep)ifworkinginsoftsoil,suchassand.Ifworkingin
hardorcompactedsoil,suchasclay,diga9”(diameter)x10”(deep)hole.
3. If installing in soft soil:Usethethreadedstaketodigintotheground
andtemporarilystabilizethexture.
If installing in hard soil:Fillthebottomoftheholewithapproximately3”
(76mm)ofpeagravel.Placethextureinholeandbackllaroundthe
xturewithsoil,uptothewireexithole.
4. MakewireconnectionsusingsuppliedQuicDisc™followingtheinstructions
below,orusingotherapprovedwiringconnectionmethod(notsupplied.)
Thexturewireisnotintendedfordirectburial.Accordingtotherequirements
oftheNationalElectricCode(NEC),directburialratedwireistobeburied
aminimumof6”[152mm]beneaththesurfaceoftheground.
5. To aim the beam:Removetheglasssealantringbyremovingthesix(6)
screwsontopofthexture.Loosenthescrewsonthesphereretaining
ringuntilthespherebecomesunxed.Aimthebeamasdesired.(upto
15°)Re-tightenthescrewsonthesphereretainingringuntilthesphereis
secure and does not rotate. Clean sealing surface, and replace glass,
gasket,andglasssealingring.Installandtorquescrewsintriangular
pattern, following the numbers screws holes 1-6.
6. Backllaroundthexturewithsoil.
SPHERE
RETAINING
SCREWS
VISDERETENUE
DELASPHÈRE
GLASS
SEALINGRING
JOINT
D’ÉTANCHÉITÉ
ENVERRE
GLASS
VERRE
GASKET
JOINT
SPHERE
SPHÈRE
THREADEDSTAKE
PIQUETFILETÉ
SOIL
TERRAIN
FOR INSTALLATION IN SOFT SOILPARA POUR
UNE INSTALLATION DANS UN TERRAIN MOU
SOIL
TERRAIN
FOR INSTALLATION IN HARD SOIL
POUR UNE INSTALLATION DANS UN TERRAIN DUR
3"(76MM)
OFPEAGRAVEL
7,5CMDE
GRAVILLONS
START
DÉBUT
TIGHTEN SCREWS IN TRIANGULAR PATTERN SHOWN ABOVE.
SERRER LES VIS SELON UN MODÈLE TRIANGULAIRE ILLUSTRÉ CI-DESSUS.
Comments to this Manuals